RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
查看: 1947|回復: 10
打印 上一主題 下一主題
收起左側

AWD 彈弓一問

[複製鏈接]
跳轉到指定樓層
1#
tonytjia@zone 發表於 2007-3-30 00:40:11 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式

遊客登錄

您需要 登錄 才可以下載或查看,沒有帳號?新玩家註冊

x
有無人用京商出的AWD彈弓?
好唔好?
2#
scalpel 發表於 2007-3-30 00:42:26 | 只看該作者
原帖由 tonytjia@zone 於 2007-3-30 00:40 發表
有無人用京商出的AWD彈弓?
好唔好?


Yes! I am using, the yellow one(hard)
3#
xlarge 發表於 2007-3-30 02:50:04 | 只看該作者
原帖由 tonytjia@zone 於 2007-3-30 00:40 發表
有無人用京商出的AWD彈弓?
好唔好?

都叫ok既........
不過要自己cut
有d麻煩
宜家當然係買PN好
唔洗cut又多度數
4#
 樓主| tonytjia@zone 發表於 2007-3-30 14:37:45 | 只看該作者

回復 #3 xlarge 的帖子

I have PN spring when I use it my car lost control when I turn.
My setup is as following:

- Benz CKL Vodafone
- AD PCB no fet
- AD Stock motor
- 19/29 A2/B2
- PN Motor heat sink
- Front 1 Degree Camber, Rear 2 Degree Camber
- Front & Rear Atmoic ball diff.

Can you share how you set up your front and rear using PN spring?
5#
xlarge 發表於 2007-3-30 15:00:14 | 只看該作者
原帖由 tonytjia@zone 於 2007-3-30 14:37 發表
I have PN spring when I use it my car lost control when I turn.
My setup is as following:

- Benz CKL Vodafone
- AD PCB no fet
- AD Stock motor
- 19/29 A2/B2
- PN Motor heat sink
- Front 1  ...

你用咩o太
6#
 樓主| tonytjia@zone 發表於 2007-3-30 20:22:53 | 只看該作者

回復 #5 xlarge 的帖子

I use atomic 20 degree no pattern front
rear atomic 10 degree with pattern
7#
ganboy 發表於 2007-3-30 22:11:54 | 只看該作者
do you apply tyre glue?
are your ball diff. set up properly?
which spring do you use in both front & rear?

To make your suspensions w/ PN spring work properly, you should add spacers(shims) on each knuckle, you may start with adding 0.8mm at bottom & 0.4mm on the top on each corner, and adjust the droop by adding and removing shims to suit your driving style but make sure not to preload springs...

If you dont add any shims under PN springs, the ride height of your AWD is certainly too low. Moreover,  given the very large droop value, you car will be very responsive. this may refer to why you lose control when cornering.

What you need to buy is a set of 3mm shims a set of 4mm shims from PN, other brands may not fit into your knuckles.

enjoy your AWD!
8#
 樓主| tonytjia@zone 發表於 2007-3-30 23:38:46 | 只看該作者

回復 #7 ganboy 的帖子

I used double tape to stick my tyre.

What colour of PN springs shall be apply in front and rear?
White front and Green at rear?

For the shims, 0.4mm on top of the spring? 0.8mm on the bottom of kucnkle?
9#
ganboy 發表於 2007-3-30 23:58:06 | 只看該作者

回復 #8 tonytjia@zone 的帖子

White front and Green at rear should be ok for stock car
0.4 below spring, 0.8 below knuckle

Ah..one more thing, apply #15000 kyosho gear diff grease on 4 joints between kunckles and upper cover.
10#
 樓主| tonytjia@zone 發表於 2007-4-2 01:03:17 | 只看該作者

回復 #9 ganboy 的帖子

Thanks ganboy.

Finally I get the setting done and now is ok... even though not perfect...

I think I will go for SAS on my next stage.

For the shims, if I remove some from the bottom or below spring how will it affect the turning?
11#
ganboy 發表於 2007-4-2 10:21:29 | 只看該作者
remove some shims from the bottom = more droop
remove some shims from below spring = more droop & lower ride height
In general, more droop meaning more responsive with the trade off of less steering mid-corner and at corner exit.
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2024-11-1 07:20 , Processed in 0.091960 second(s), 15 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表