RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
樓主: powis
打印 上一主題 下一主題
收起左側

TOP Sabre FD 專區

  [複製鏈接]
跳轉到指定樓層
1#
powis 發表於 2010-9-26 17:54:53 | 顯示全部樓層 回帖獎勵 |倒序瀏覽 |閱讀模式

遊客登錄

您需要 登錄 才可以下載或查看,沒有帳號?新玩家註冊

x
本帖最後由 powis 於 2010-9-26 18:20 編輯

Just want to have a place to share the settings and experience on playing Sabre FD~
Welcome to post any things related to the Sabre FD, even settings, photo, related websites anything~!


                               
登錄/註冊後可看大圖
2#
 樓主| powis 發表於 2010-9-26 18:12:14 | 顯示全部樓層
本帖最後由 powis 於 2010-9-26 21:43 編輯

Let me share some experience on the Sabre FD.  I am a beginner on front wheel car.
Today just try it on JV track, bascially followed the most settings on the setup sheet from TOP. The details are:

Camber : F & R are 2 degree
Toe : F  toe in 1 degree, R default
Dampers spring : original one
Dampers oil : F35 R30
Downstop : F and R are 3mm
Ride height : F 4.5mm R 5.5mm
Motor : SpeedPassion competition 13.5RPinion gear : 18T
ESC : Hobbywing 120A with turbo mode
Tire : 36R

When I decrease the throttle while go into 灣, the car will "Nut"尾 at the 灣尾.  反而when the speed is high and go into and leave the 灣 , with the low turning angle, the car can smooth to go.

Sometime when i try to accelerate a bit during cornering, the car will easy to cup 4.

So generally i think that i still need time to set up the car correctly for JV, but the feeling is good when the car is cornering on some low speed  灣 because the car cornering response is fast, or too fast.
3#
 樓主| powis 發表於 2010-9-26 18:29:54 | 顯示全部樓層
Support TOP
師兄係邊度玩多

小弟都入左架 SABRE,不過仲未完成
利物浦 發表於 2010-9-26 18:00


I just tried the car on JV today only!
4#
 樓主| powis 發表於 2010-9-26 21:53:23 | 顯示全部樓層


Forget to say i was using 18T.
Gear ratio is 6.44
5#
 樓主| powis 發表於 2010-9-26 22:01:13 | 顯示全部樓層
跟車果 set 彈弓係
頭 344 = 19.2 lb
尾 306 = 17.1 lb
利物浦 發表於 2010-9-26 21:59


thank you for your information
6#
 樓主| powis 發表於 2010-9-26 22:32:42 | 顯示全部樓層
C Hing Powis, do you mean 灣尾 as corner exit?

"when the speed is high and go into and leave the ...
Chrispo 發表於 2010-9-26 22:08


Yup, i means the corner exit.

Yup too, actually i was talking about the corner after the long straight road in JV.  i found that i full speed enter and exit the corner with the minimum turning  angle is easier to control.
7#
 樓主| powis 發表於 2010-9-26 23:10:02 | 顯示全部樓層
Will that be a bit too fast?

Meanwhile, if using the TOP gear diff, what degree of diff. gear ...
Chrispo 發表於 2010-9-26 23:02


But i heard that TOP gear diff is very easy to damage...anybody tried this ?
8#
 樓主| powis 發表於 2010-9-26 23:35:04 | 顯示全部樓層
回復  powis

i once heard that the gear diff. of top sabre is same as tamiya's m03.  
but i am n ...
1524 發表於 2010-9-26 23:28


I heard that the gear diff for Photon also can be used on Sabre (from one of the shop in KWS), but also heard that gear diff is very weak and easy to damage...
9#
 樓主| powis 發表於 2010-9-27 09:47:25 | 顯示全部樓層
C兄,我想請問你有冇個TUBRO SETTING 呀?我都係玩呢部KA ,有機會一起玩啦!!
ae110hk 發表於 2010-9-27 03:53


I have forgot the exact setting right now, just remember i use the max turbo level and timing, and the turbo delay is 0.1 and it will start at 6000rpm.
10#
 樓主| powis 發表於 2010-10-2 01:14:07 | 顯示全部樓層
Today tried some set up tips from "high hand" and found that using the lower traction tire at front which can really help the car stability and my car now much less "nut" now!
11#
 樓主| powis 發表於 2010-10-2 02:51:50 | 顯示全部樓層
BTW anyone know TOP have released the spool diff for Sabre FD? or need to modify it myself from the ball diff (even i think it is not hard to do)?
12#
 樓主| powis 發表於 2010-10-2 12:28:28 | 顯示全部樓層
回復  powis

頭用 lower tracion tyre....唔會令架車更傾各甩頭 (入唔到灣咩)?
不過你講高手set 過. ...
1524 發表於 2010-10-2 09:31


I also have same feel at the beginning when i heard that idea, but after try this, it really run much better.  I just bought some cheap price tire like (Swxxp or Solaxxx).
13#
 樓主| powis 發表於 2010-10-3 23:38:31 | 顯示全部樓層
今日試左車  ,唔知點解 FF車會甩尾,仲甩得好勁 一入彎就調頭  要就住就住先玩到 但架車入彎反應同速度都好快 ...
rcmodel 發表於 2010-10-3 23:08


both front and rear use Sorex 36R ?
14#
 樓主| powis 發表於 2010-10-6 00:24:40 | 顯示全部樓層
避震腳同臂嘅波頭合上時好緊,其他車友有冇以上情況出現?
mugenstream 發表於 2010-10-5 19:48


my one do not have this problem.
15#
 樓主| powis 發表於 2010-10-6 23:08:59 | 顯示全部樓層
Today test the FD onJV again, using Solaris Hard tire on front and Sorex 36R on rear, run very good, and set the height ride lower, this time the car run very nice, no more "CUP 4"  and run much stable then using both 36R on front and rear.  But still have to fine tune the car to make the car response better.
16#
 樓主| powis 發表於 2010-10-7 17:23:44 | 顯示全部樓層
Ok la, 最緊要幫到手, 呢架車真係一架好野來架.
ben3210 發表於 2010-10-7 16:29


有幾好先
17#
 樓主| powis 發表於 2010-10-8 00:27:35 | 顯示全部樓層
你一換front Solaris and rear 36R後你都寫到禁好, 到你fine tune 後就真係 ...
ben3210 發表於 2010-10-7 18:20


Yea agree.

Now my car is just can run normally, but absolutely not very nice on handling.  so really need put more effort on it.  So any idea on fine tuning this car?
18#
 樓主| powis 發表於 2010-10-8 08:09:25 | 顯示全部樓層
你試下用隻比較大尾定風翼,將頭避震机裝最斜位置 (好似FF03尾避震要最斜) 試下有冇幫助。
ben3210 發表於 2010-10-8 07:13


OK let me try try this!

Thank you for your tips!
19#
 樓主| powis 發表於 2010-11-17 00:40:56 | 顯示全部樓層
大家在 JV 玩用咩setting ...TOP Sabre FD ..
sing.kh8212 發表於 2010-11-14 18:52


Page 1 to 3 have some of my experience on JV, it is work geh.
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2024-6-13 05:03 , Processed in 0.041445 second(s), 18 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表