等左個幾月........Axial AX10 Scorpion crawler

me, over 10 hour
80% finish...........

原帖由 edison 於 2007-11-8 00:11 發表

                               
登錄/註冊後可看大圖

Red star have 2boxs ar!!
just HKD1900, is much cheap then me la!
I buy this kit form US, total need HK2200!!

你早人成2個月.....乜都抵la....
個2個月等到我

原帖由 simontam 於 2007-11-9 11:33 發表

                               
登錄/註冊後可看大圖

me, over 10 hour
80% finish...........

keep posting photo and share with us
nice  

Hi All Bros,
Just bought it tonight at KWS- HS.
Hope to know what brand how much of motor & ESC used on your crawler?
And the servo need more torque? ??Kg/cm
Thanks for all.

原帖由 fyin 於 2007-11-9 23:27 發表

                               
登錄/註冊後可看大圖

Hi All Bros,
Just bought it tonight at KWS- HS.
Hope to know what brand how much of motor & ESC used on your crawler?
And the servo need more torque? ??Kg/cm
Thanks for all.

may i know how much u bought at HS ?
i use mc330 with 3A BEC, Integy 50t moto, towerpro mg995 servo(using mg995 servo, u must add BEC on your esc, or u must have 2a bec on your esc)

Hi Bro,
What's the function to use separate BEC.to the ESC?
Is the main batt connect to ESC and receiver to control 2 servos.
the reciever with BEC inside, or built-it BEC's current not enough?
Thanks Bro.

HS 1980
CAT 2000

原帖由 fyin 於 2007-11-10 00:40 發表

                               
登錄/註冊後可看大圖

Hi Bro,
What's the function to use separate BEC.to the ESC?
Is the main batt connect to ESC and receiver to control 2 servos.
the reciever with BEC inside, or built-it BEC's current not enough?
T ...

most ESC "built-in BEC's current not enough" so it need a bigger "A" BEC to give more power to servo, otherwise, the servo will stop while you turn left, right. or burn your esc.

check this out

                               
登錄/註冊後可看大圖

http://bbs.rc-evo.com/viewthread.php?tid=61037&extra=page%3D1

Hi Bro,
Thanks your advise, will get one for my AX10.

原帖由 kaho0338 於 2007-11-9 23:38 發表

                               
登錄/註冊後可看大圖

Towerpro mg995 servo(using mg995 servo, u must add BEC on your esc, or u must have 2a bec on your esc)

Where did you buy the MG995?  Is this servo good enough for AX10 crawler application for it's price?

Please advise.

原帖由 Ang 於 2007-11-10 11:51 發表

                               
登錄/註冊後可看大圖

Where did you buy the MG995?  Is this servo good enough for AX10 crawler application for it's price?

Please advise.

sure, i bought at here from other brothers, the price is $70
very good on ax10

原帖由 fyin 於 2007-11-10 10:02 發表

                               
登錄/註冊後可看大圖

Hi Bro,
Thanks your advise, will get one for my AX10.

it depend on on what ESC you using!
I know some ESC can output 6V, 5A BEC power.

Novak ROOSTER CRAWLER-EDITION




ROOSTER CRAWLER-EDITION FEATURES  
2 specifically designed crawling driving profiles which feature Zero Reverse Delay, and high-powered Drag Brakes (or “Hill” or “Hold” brakes)
Built-in Li-Poly Cutoff Protection (Profile 2)
Water-Resistant Case
Heavy-Duty 6 Volt / 5 Amp BEC
Direct-Solder Wiring Tabs
User Replaceable Input Harness
Novak’s One-Touch Set-Up™
Built-in Power Output for Optional 6V Accessory Fan (#5648)
Novak’s Radio-Priority Circuitry™

Novak’s Polar Drive Circuitry™
Thermal Overload Protection
Designed and Assembled by Novak in the USA using globally sourced components

ROOSTER CRAWLER-EDITION SPECIFICATIONS  
Forward/Reverse:  Forward and Reverse
Input Voltage:  4-7 Ni-Cd/Ni-MH cells (1.2V/cell) or 2 Li-Poly cells
Footprint:  1.54" x 1.18" (39 x 30 mm)
Weight:  2.66 oz. (75.5 g) w/wires; 1.57 oz. (44.5 g) w/o wires
Motor Limit:  12-turn brushed (at 6 cells Ni-MH)
On-Resistance:  0.0014 ohms (forward); 0.0028 ohms (reverse)*
Rated Current:  400 amps* (forward)

Braking Current:  200 amps*
BEC:  6.0 volt/5.0 amp
Motor Limit 27-turn brushed (at 6 cells Ni-MH)

Discrete Steps:  256 Forward; 256 Reverse
Battery Plug:  Tamiya
Motor Plug Bullet connectors
Drive Profiles: 2
Status LEDs: 2  
Voltage Cut-off: 6.25 volts (Li-Poly Profiles)

原帖由 edison 於 2007-11-10 12:15 發表

                               
登錄/註冊後可看大圖

it depend on on what ESC you using!
I know some ESC can output 6V, 5A BEC power.

Novak ROOSTER CRAWLER-EDITION




ROOSTER CRAWLER-EDITION FEATURES  
2 specifically designed crawling dri ...

好貴
不如買你隻brushless 好過

Hi Bro edison,
Thanks your info.
I will use Hitec servo 645MG or 5945MG.

Just check the Novak Crawling edition price around US$89.99.

原帖由 fyin 於 2007-11-12 14:19 發表

                               
登錄/註冊後可看大圖

Just check the Novak Crawling edition price around US$89.99.

which esc planning to use now ?

原帖由 kaho0338 於 2007-11-10 01:32 發表

                               
登錄/註冊後可看大圖

most ESC "built-in BEC's current not enough" so it need a bigger "A" BEC to give more power to servo, otherwise, the servo will stop while you turn left, right. or burn your esc.

check this out ...

does any bro know whether this extra BEC can be used in brushless Esc ??......... many thx !!

原帖由 minimini 於 2007-11-13 02:04 發表

                               
登錄/註冊後可看大圖

does any bro know whether this extra BEC can be used in brushless Esc ??......... many thx !!

this is my BEC manual, u can have a look.....hope it can help
http://www.hobbywing.com/upload/UBEC_new.pdf
http://www.hobbywing.com/product_show.asp?ID=75

anyway, u got ax10 too ?

[ 本帖最後由 kaho0338 於 2007-11-13 02:10 編輯 ]

原帖由 kaho0338 於 2007-11-13 02:09 發表

                               
登錄/註冊後可看大圖

this is my BEC manual, u can have a look.....hope it can help
http://www.hobbywing.com/upload/UBEC_new.pdf
http://www.hobbywing.com/product_show.asp?ID=75

anyway, u got ax10 too ?

Thx bro kaho........

I got the TLT only (with Tobee extension pack)........

原帖由 minimini 於 2007-11-13 02:12 發表

                               
登錄/註冊後可看大圖

Thx bro kaho........

I got the TLT only (with Tobee extension pack)........

o...it can use on brushless esc
i checked the manual

but better ask ask b4 u buy

[ 本帖最後由 kaho0338 於 2007-11-13 02:18 編輯 ]