焊接問題..

現附上貼圖，希望可以提供作參考~~~

四個字
經驗搭救

有圖睇好有用!...多謝C Hing!

辣雞唔駛話要大火數去到100W,60W已經足夠.
好O既牌子辣雞恆溫準,足夠焊到電有餘.

100W果O的賣已經係犯法.用時不單止危險,仲容易熱得濟,會損壞O的電子零件(過熱)

最重要係買一支好O的O既辣雞,如GOOT或HAKKO.
另外就係要知自己焊O的乜為主.

如果係焊電,咁就要買支可以換如KKCHUNG所講O既果種焊咀.
如果只係焊下接頭O既,尖頭都可以.

我宜家有兩支,一支GOOT TQ95,一支係HAKKO RED 503
最好用係果支HAKKO.

另外,唔好慳果一個幾毫,買O的好O的O既焊錫.
如GOOT,最低限度都買果O的黃色蓋一筒筒果O的.....
除非你日日焊,唔係唔好買一大圈果O的,果O的你唔會用得晒之餘,仲會氧化....氧化咗果O的錫不單錫得唔好,仲好難上錫.

多謝, 多謝晒... 各C Hing 指教 !!   我終於成功咗喇..!!! Yeah !!

.......................sorry

記得留意下通風, 唔好吸左D煙...好冇益架~

記得留意下通風, 唔好吸左D煙...好冇益架~
console001 發表於 2010-4-28 22:56

                               
登錄/註冊後可看大圖

係既...大大

非常詳細既解答

同埋
焊錫D煙有毒?死啦仲成日聞,覺得好香

等我下次拎去燒焊
tai13 發表於 2010-4-28 22:39

                               
登錄/註冊後可看大圖

點1點粒電都溶埋

點1點粒電都溶埋
kungyuen 發表於 2010-4-28 23:10

                               
登錄/註冊後可看大圖

    今先考功夫

我都要'浸'吓焊接嘅功夫...真係好多細節嘢要注意...  好彩有咁多c hing 教我..!謝謝

睇完咁多位c兄d經驗真係學唔少野

去5金舖買d"松香膏"塗少少o係面先上錫~~~
好平架咋~~用左好焊好多~~可以試下http://v.youku.com/v_show/id_XMjQyMjg0OTI=.html

http://v.youku.com/v_show/id_XMjQyMjg0OTI=.html

去5金舖買d"松香膏"塗少少o係面先上錫~~~
好平架咋~~用左好焊好多~~可以試下
skpaul 發表於 2010-4-29 01:33

                               
登錄/註冊後可看大圖

呢句野咁似我講o既??

ching, I suggest you to buy a dual-power solder gun ( my one is 40W, can switch to 200W for 30sec ), solder T-plug must be hot enough and in very short time, otherwsie the T-plug plastic will melt. Buy some better 錫線 but no need to buy very expensive "silver-content" 錫線, because the silver type "sounds better" for audio use, RC do not need this grade.
   
Clean both surface by alcohal to remove oil-layer and ensure it's dry, then apply just a little 松香膏, that's it. The last secret of good solder is to practise and practise !

登錄/註冊後可看大圖