Subaru Brat試車記(#27有part2+#18新增維修點滴......)

稱唔上一個report……

直路係用黑豬都已經好快o既，只係頭轉向真係好唔得！

全原裝車o既頭金屬轉向杯竟然為左避1:1，撞左一次就分成兩件！救命！
servo saver爆埋！冇得試車！

睇怕都係換其他車o既o野落去先好跑……

[ 本帖最後由 smallfaifai 於 2007-8-5 22:53 編輯 ]

原帖由 ryancmlam 於 2007-8-5 23:02 發表

                               
登錄/註冊後可看大圖

DF03 sure. go go go...

魔鬼呀！~~~ :21: :21: :21: :21: :21: :21: :21:

呢兩日唔落KWS住！豈有此理！

DF03 sure. go go go...

混合膠似乎work喎！今日o係TKO咁o既環境一D事都冇……

不過架車o既轉向真係好唔掂，轉得太多啦……加上今日只有一個cheap雞AM控，冇計……

同埋原裝轉向推杆真係好「雞」，玩第二次已經變形……要換啦！

仲有就係原裝呔o係TKO環境完全唔得，一D都唔咬……一擺落地大啖D油已經原地打轉……

冇眼睇！又要換呔！定係真係搵架DF03去……！？

我又唔識個牌子就是但啦，點知.......唔理啦，聽日試車再算啦。

Araldite is absolutely useless. Use JB Weld la.

good luck.

good luck for your epoxy glue

初步試驗都似乎係work既....希望聽日順利吧。

If the epoxy doesn't work (it is the likely case coz the "gl;uable" area is so small), try this 魔術鋼膠. Very strong.

http://www.henrychemical.com/itm00004.htm

先謝.....希望係啦.....

instruction話要等3個鍾先會較實淨，今晚試一試先......

夜少少要整埋個servo saver落去.....

[ 本帖最後由 smallfaifai 於 2007-8-4 19:21 編輯 ]

I don't have this tool, therefore my result was not good.
Good job, I think your result should be fruitful!!

買左混合膠，試下黐番，睇下效果如何……

原帖由 gibson 於 2007-8-1 16:05 發表

                               
登錄/註冊後可看大圖

We have experienced the same problem, one of the bro ordered this pair of steering arms for HKD105 per pair.

Gibson兄你自己有冇訂？

我估都係去創x或偉x訂，然後等個零月吧……

We have experienced the same problem, one of the bro ordered this pair of steering arms for HKD105 per pair.

原帖由 beat 於 2007-8-1 15:34 發表

                               
登錄/註冊後可看大圖

yes it has just ask any glue can stick on metal is ok

Cool!~
Thx Bro.!~

晏少少出街搵先！

yes it has just ask any glue can stick on metal is ok

原帖由 beat 於 2007-8-1 15:29 發表

                               
登錄/註冊後可看大圖

you have same case with Mr Gibson, i think u need a Epoxy glue to glue back the shaft to the up right, this is one of the Re-release defect from the frog and subaru Brat

Epoxy glue 即係鋼膠o個類o野？五金鋪有嗎？

you have same case with Mr Gibson, i think u need a Epoxy glue to glue back the shaft to the up right, this is one of the Re-release defect from the frog and subaru Brat

原帖由 gibson 於 2007-7-31 19:23 發表

                               
登錄/註冊後可看大圖

I may have spare parts, post a picture which parts was broken la!!

Thx bro.!~

以下係損毀狀況……

提提大家，原裝推桿特幼！而且轉向杯波頭set死左係4mm，即係一定要換杯先可強化……

由於比較忙，都仲未有時間試換lunch box的落去……

[ 本帖最後由 smallfaifai 於 2007-8-1 15:30 編輯 ]