Tamiya Buggy

I'm beginner and looking for a Tamiya Buggy. I could want to what is the difference in between #58596 and #58568? And which is better?

哈哈我唸住加左無咁易爛

airhole 發表於 2015-2-12 19:11
我想問前外置BUMPER的sponge應該係什麼part no?

其實 sponge bumper 係唔係比呢類 buggy 用㗎？我見好似房車嗰類用多
我係新手乜都唔識，有錯請指點

Thk.3mm frp damper stay 比原裝硬淨好多

kitman 發表於 2015-2-12 21:58
唔好意思!我記錯咗，我用咗頂油壓果隻damper urethane bushing 頂住佢

唔緊要
我最後前塞O-ring，後面揾咗條 silicon tube 塞入去頂住，而家只剩1mm左右虛位，應該無乜大問題了。
奇怪在支軸明明可以做長少少，或者跟多一粒O-ring已經好好多...竟然要自己想辦法DIY

alexmichael 發表於 2015-2-12 18:53
唔知係唔係裝錯...

唔好意思!我記錯咗，我用咗頂油壓果隻damper urethane bushing 頂住佢

我想問前外置BUMPER的sponge應該係什麼part no?

kitman 發表於 2015-2-12 18:38
我裝咗。但係加咗o ring無虛位喎。

唔知係唔係裝錯...

alexmichael 發表於 2015-2-12 18:14
請問點解54501+2 Al.propeller shaft  & joints 裝落車前後虚位咁大...
塞個粒 o-ring 入鋁杯内都無乜作用. ...

我裝咗。但係加咗o ring無虛位喎。

重複,deleted

請問點解54501+2 Al.propeller shaft  & joints 裝落車前後虚位咁大...
塞個粒 o-ring 入鋁杯内都無乜作用...
前面個 joint 有機會走位鬆出嚟少少有無問題㗎?

Hi Ching, which paint you used for dual ridge body?

kitman 發表於 2015-2-10 22:44
RCmart 見有貨。
不過我覺得頭OK,尾油壓架就太弱。

Thanks, 已在 RCmart 訂咗。前後換晒感覺上舒服啲...

965 發表於 2015-2-10 00:56
Yes ..  ball bearing is a good idea ..  just 幾十蚊, 已經有電變, 平平地買個 10.5 T 麼打 .. 夠 la ..  ...

原裝ESC說明書講10.5T齒比唔好去咁盡OR加風扇可以減小overheat

alexmichael 發表於 2015-2-10 19:33
我都入咗 dual ridge，搵緊原廠前後 frp damper stay. 請問有無師兄知邊度有貨？Thanks. ...

RCmart 見有貨。
不過我覺得頭OK,尾油壓架就太弱。

我都入咗 dual ridge，搵緊原廠前後 frp damper stay. 請問有無師兄知邊度有貨？Thanks.

Thx buddy

Yes ..  ball bearing is a good idea ..  just 幾十蚊, 已經有電變, 平平地買個 10.5 T 麼打 .. 夠 la ..

Thx all.
Is necessary replace the bearing with Teflon Ball Bearing?

I only change the followings:
1. Aluminum Propeller Joint;
2. Aluminum Motor Mount ; and
3. Aluminum Propeller Shaft .