想玩蛇的朋友,看後會否要再考慮呢 ?

今天在jv拍的....那師兄只是和一大腳輕微碰撞後.....
以為rim會比較大損傷...點知.......

難道所有新車都是軟皮蛇?!!!!

回復 10# winclearly


    So dead snake

要玩靚料12仔~ 一定要玩MADE IN USA/ MADE IN JAPAN
RC12L3啦~

x-ray samething......  To be hornest CRC seems to be better.  I play R5 and my friends runs CRC, serpent, r5.1, x-ray, yokomo....  Only the CRC and r5 do not have much issue.  Even the 5.1 seems to be weaker than the r5.....

已前啲貴零件如果用7075就一定有註明.
現在已好少會標明佢用乜野料做就知喇.

可能用既鋁料已經唔係7075, 改咗啲低guide既鋁料做.
因7075現在真的好貴, 好多模型廠商都冇可能用得起或者都唔會用. (成本高+損耗大)
就算用啲產品出街價都好貴.
我向廣東道都係找到最高檔都係6061.

宜家d野咁化學架咩...

Made in china is not the problem, it's the quality control.
It is obvious that the alloy is low grade.

Everything is made in China now!! SAD!

好明顯,質料差左好多....

回復 14# abcde


    i have ordered la, if world model have stock,, i should get in today..

哩"post"真係,

你玩 "蛇"; "蛇"玩你.  
咁講, "蛇 proten pancar" 又點呢？

haa.. it seems no good quality 12 son now. still any good quality 12son out there? Xray?
airyu 發表於 2010-11-9 09:57

                               
登錄/註冊後可看大圖

have  buy back that parts (right hub) ?

haa.. it seems no good quality 12 son now. still any good quality 12son out there? Xray?

ching,我玩960-07蛇,d萬向系Hudy做,膠料系荷蘭做,
但自960-08開始,所有平地蛇d零件(buggy例外)己經轉了 ...
winclearly 發表於 2010-11-7 22:21

                               
登錄/註冊後可看大圖

agree.  Their quality used to be very good......  my friends s120 have same issue.  And the center thread for the main shaft pull out only after few runs......

That's too bad.  

There are so many cars in JV; touring, monster, slash, buggy, 1/12, M, FF with different levels.  If there are many cars on the track, I usually stop @ pit and wait until there are less cars.

部車是坐我隔離的12仔蛇.....
佢初玩後驅..巳玩得比較小心的了..見佢和大腳微微撞了一下..以為只是尾rim灣 ...
abcde 發表於 2010-11-7 20:22

                               
登錄/註冊後可看大圖

ching,我玩960-07蛇,d萬向系Hudy做,膠料系荷蘭做,
但自960-08開始,所有平地蛇d零件(buggy例外)己經轉了X球,在大陸廠做,所以d質量很差,d960-08蛇,新車d啤呤己不順,油缸漏气(包括733),膠料很弱,d質量差但價錢和x-ray差不多,所以我己冇玩蛇了

impossible... this is too weak...

so hurt~~~~~~~~