RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: TA02 arms question. [打印本頁]

作者: Beer 時間: 2009-7-25 22:07
標題: TA02 arms question.
Can any brother know what is the difference between the two sets of arms?

作者: kkchung 時間: 2009-7-25 22:11
上面是TA01用，下面是TA02或FF01。當年TA01是用回魔鬼魚車架，用後臂向前等前後軸短些而重心也較後。而TA02便改短了主車架，然後把後臂向後伸這樣來使重心前些。

作者: Beer 時間: 2009-7-25 22:19

上面是TA01用，下面是TA02。
kkchung 發表於 2009-7-25 22:11

登錄/註冊後可看大圖

Thanks kkchung, may I know any advantages between them? If I buy, which pair is better?

作者: msmcreation 時間: 2009-7-25 23:05

Thanks kkchung, may I know any advantages between them? If I buy, which pair is better?
Beer 發表於 2009-7-25 22:19

登錄/註冊後可看大圖

兩款臂俾兩款唔同o既車用, 你有TA01 就用TA01臂; 你有TA02就用TA02臂...
TA01裝TA02後臂wheelbase會長左...TA02網TA01臂Wheelbase會短左
兩個情況都裝唔到正常touring 殼

作者: kkchung 時間: 2009-7-26 04:56
特然想起TA02SW也是用上方的A臂，應是連銀色波箱殼及911 GT2車殼出售。

作者: 一匹狼 時間: 2009-7-27 00:51
我又問

我有架ta02sw,其實佢係short係係邊部份同wide係邊部份?
如果我想轉返做普通ta02,用返d正常殼
要換d咩?

作者: kkchung 時間: 2009-7-27 01:31

我又問
我有架ta02sw,其實佢係short係係邊部份同wide係邊部份?
如果我想轉返做普通ta02,用返d正常殼
要換d咩?
一匹狼發表於 2009-7-27 00:51

登錄/註冊後可看大圖

(01)和TA02短在用了TA01反向前的後A臂。而寬只是原裝呤是向外走出了。
(02)只要換回正常02後A臂和呤便可。

作者: 一匹狼 時間: 2009-7-27 16:34
我尋晚睇睇下都發覺原來係反向裝所以短左...
調返轉WHEELBASE去返257MM左右,得左

雙星D軨係咪本身有OFFSET...?
如果用190MM殼,用OFFSET 0的車軨得吾得?
定係多數黎講係要用OFFSET 2的車軨?
另外要配返幾多MM六角?
想轉玩200MM殼又難吾難呢...?

問題較多,吾好意思!

作者: kkchung 時間: 2009-7-27 23:10

我尋晚睇睇下都發覺原來係反向裝所以短左...
調返轉WHEELBASE去返257MM左右,得左

雙星D軨係咪本身有OFFSET...?
如果用190MM殼,用OFFSET 0的車軨得吾得?
定係多數黎講係要用OFFSET 2的車軨?
另外要配返幾多M ...
一匹狼發表於 2009-7-27 16:34

登錄/註冊後可看大圖

沒記錯以前賣W字尾車的原裝呤是分體式可變OFFSET。
是的換呤便可以。

作者: chowhungjai 時間: 2009-7-28 01:06
I wondering are there anybody who know where I can found 賽鋼 arms for ta02

作者: jonni2000 時間: 2009-9-26 18:05
I GUESS YOU COULD USE THE TA01 REAR CONTROL ARM ON A TA02 CHASSIS, THE REASON IS WHEN EVER YOU LOWER THE TA02 CHASSIS, THE REAR TOE BECOME TOE IN AND I DON'T THINK THERE IS A WAY TO ADJUST IT STRAIGHT, AND THAT'S WHAT I DID THE STRAIGHTEN THE REAR TOE BY USING THE TA01 REAR CONTROL ARM ON A TA02 CHASSIS

作者: jonni2000 時間: 2009-9-26 18:07
I HAVE A TA02 CHASSIS CONVERTED TO MR AND I GOT ALL THE ALUMINUM PARTS FROM THIS WEB-SITE, PARTS ARE REALLY CHEAP AND WORKS PREFECT, THE WEBSITE IS CALLED WWW.ASIATEES.COM, I THINK THEY ARE LOCATED IN HK, BUT IM NOT SURE WHERE IS THE LOCATION

作者: jonni2000 時間: 2009-9-26 18:09
I'M USING A 3MM OFFSET ON A TA02 CHASSIS FOR A 200MM AND STILL COULDN'T GET THE WHEEL TO THE RIGHT PLACE, I GUESS YOU MIGHT NEED A 6MM OFFSET FOR THE TA01, 02 CHASSIS

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)