有得玩 DF-03 啦

下次 TKO Off-road Party 可以同各位 brothers 片過。

[ 本帖最後由 li5115 於 2007-7-10 18:30 編輯 ]

恭喜!!!!!!!!!!!!!!!!!好型呀

好型,,不過玩完成架泥..呵呵

nice buggy !!

congrats,,,,,,
one more TKO DF03 member!!

嘩......表面都好補呀 ! 反牙 / 硬 ball end / 油壓 / C 座 / 油壓板 / 轉向杯 / 萬向

well done....!
The standard of new DF03 players is very high!!!

the shell looks good wor.........  ........what color is it ??.......is it Tamiya color ??...... Thx !!

原帖由 minimini 於 2007-7-10 09:35 發表

                               
登錄/註冊後可看大圖

the shell looks good wor.........  ........what color is it ??.......is it Tamiya color ??...... Thx !!

星星 透明綠 再用 gun metal 做底。

[ 本帖最後由 li5115 於 2007-7-10 11:29 編輯 ]

Woooooooooo........  齊料齊料..............  用乜摩打呀???  有冇 sip 介子落前suspension 芯度呀??  下次TKO好可能係呢個星期日.......  

原帖由 bigben 於 2007-7-10 09:33 發表

                               
登錄/註冊後可看大圖

well done....!
The standard of new DF03 players is very high!!!

Just when I wanted to buy a stock DF-03 to join the fun tim

原帖由 mikewu 於 2007-7-10 11:34 發表

                               
登錄/註冊後可看大圖

Woooooooooo........  齊料齊料..............  用乜摩打呀???  有冇 sip 介子落前suspension 芯度呀??  下次TKO好可能係呢個星期日.......  

BZ。前 suspension 芯是否指前臂呀？我用咗 SSG Graphite Suspension Brace。

原帖由 li5115 於 2007-7-10 18:38 發表

                               
登錄/註冊後可看大圖

BZ。前 suspension 芯是否指前臂呀？我用咗 SSG Graphite Suspension Brace。

Nicey nicey.....  "fully loaded"....
There will be a TKO party this Sunday, please come and join....

What I meant about the suspension, is there is a gap in between the chassis and lower control arm..... Red the top page where I have highlighted in color red and find out....  Otherwise your turning knuckle might hit the control arm..

原帖由 mikewu 於 2007-7-10 21:50 發表

                               
登錄/註冊後可看大圖

Nicey nicey.....  "fully loaded"....
There will be a TKO party this Sunday, please come and join....

What I meant about the suspension, is there is a gap in between the chassis and  ...

I use this one.

Hi Mike,
Hows the performance for the centre one way, is it good for turning?
Do you know the difference between the centre one way and the front one way.

顏色配搭仲好過原本設定

原帖由 li5115 於 2007-7-11 16:40 發表

                               
登錄/註冊後可看大圖

Hi Mike,
Hows the performance for the centre one way, is it good for turning?
Do you know the difference between the centre one way and the front one way.

I only use front one way and the cornering is much much stablier then it used to be... never tried the centre one way.....  sorry can't help...  

原帖由 mikewu 於 2007-7-12 01:38 發表

                               
登錄/註冊後可看大圖

I only use front one way and the cornering is much much stablier then it used to be... never tried the centre one way.....  sorry can't help...  

I use front one way too. According to 健全(星星亞洲盃-Buggy香港代表)，he say no stablizers were need for off-road(on-road only)。

原帖由 courel500 於 2007-7-9 19:40 發表

                               
登錄/註冊後可看大圖

嘩......表面都好補呀 ! 反牙 / 硬 ball end / 油壓 / C 座 / 油壓板 / 轉向杯 / 萬向

入面都過得去