Question about OS Engine

What is the different between this 2 OS engine and which one will fit the most for FW-05T+ ar Thank you
1st (O.S. .12 TG (P)-X with 12D Slide Carburetor OSM11381)
2nd (O.S. .12 TG-X with 12E Rotary Carburetor OSM11383)

the diff are the carb and the crank shaft,
the first will be fit for your FW~05,
but also u need to buy the new one flywheel,nuts and engine mount,
hope can help u~~

原帖由 piccoengine 於 2007-7-31 03:32 發表

                               
登錄/註冊後可看大圖

the diff are the carb and the crank shaft,
the first will be fit for your FW~05,
but also u need to buy the new one flywheel,nuts and engine mount,
hope can help u~~

Thanks for your information can i use the GXR-15 flywheel and nuts for this OS engine ar. Thank you

原帖由 Eric_116 於 2007-7-31 03:42 發表

                               
登錄/註冊後可看大圖

Thanks for your information can i use the GXR-15 flywheel and nuts for this OS engine ar. Thank you

u can use the GXR15 flywheel,but that one is very heavy,
i think use the option one will be better,
and the nut cannot use,because the tooth pitch is not fit for the SG crank shaft~

O.S. .12 TG-X with 12E Rotary Carburetor OSM11383
呢副機條crackshaft係全牙,
可以用你原裝個條engine nut(冇話重唔重既,flywheel就要買番kyosho出俾os個套)
個化油器既啟動同上方唔同(以推上推落既方式進行油門行動)
O.S. .12 TG (P)-X with 12D Slide Carburetor OSM11381
呢副機條crackshaft係半牙,
要用推掌先可以install到d gears(但係有另一個方法,平靚正,唔同你地講)
個化油器既結構就係好似gxr15 engine咁既方式操縱油門

緊係買呢個la 12 tg Slide Carburetor
http://www.os-engines.co.jp/line_up/engine/car/catalog/11386.html
但係仲未出手拉

Eric 兄 又換機@.@?

Eric兄 不是用來玩Drift 嗎.. OS-18TM / 18CV-R ...大力+食油的

原帖由 RGM-111 於 2007-8-1 00:52 發表

                               
登錄/註冊後可看大圖

Eric兄 不是用來玩Drift 嗎.. OS-18TM / 18CV-R ...大力+食油的

Yes ar looking some engine with better $$
OS-18TM / 18CV-R ...大力+食油的 can u give me some infomation ar. Thank you

[ 本帖最後由 Eric_116 於 2007-8-1 03:06 編輯 ]

原帖由 sunnyshao007 於 2007-7-31 09:22 發表

                               
登錄/註冊後可看大圖

O.S. .12 TG-X with 12E Rotary Carburetor OSM11383
呢副機條crackshaft係全牙,
可以用你原裝個條engine nut(冇話重唔重既,flywheel就要買番kyosho出俾os個套)
個化油器既啟動同上方唔同(以推上推落既方式進 ...

Thanks for your information

原帖由 iketani 於 2007-7-31 12:11 發表

                               
登錄/註冊後可看大圖

緊係買呢個la 12 tg Slide Carburetor
http://www.os-engines.co.jp/line_up/engine/car/catalog/11386.html
但係仲未出手拉

Any other 手拉 engine will fit the most for FW-05T+ ar b/c i don't want to use starter box ar Thank you

O.S. .12 TG-X with 12E Rotary Carburetor OSM11383
呢副機條crackshaft係全牙,
可以用你原裝個條engine nut(冇話重唔重既,flywheel就要買番kyosho出俾os個套)  <---------(1)
個化油器既啟動同上方唔同(以推上推落既方式進行油門行動)
O.S. .12 TG (P)-X with 12D Slide Carburetor OSM11381
呢副機條crackshaft係半牙,
要用推掌先可以install到d gears(但係有另一個方法,平靚正,唔同你地講)  <----------(2)
個化油器既結構就係好似gxr15 engine咁既方式操縱油門


(1)Sunny兄  OS12TG-X 全呀條shaft  好像都是M5粗 , 應該用唔到FW-05T+ 個粒2speed Nuts.....(有錯請各位指教)..我的OS Engine是用kyosho (VSW-059) 個粒2speed Nut 的, 反而個Flywheel可以用番..不過我都係換了個輕的

(2)相信好多人都想G  

http://www.os-engines.co.jp/line ... atalog/11296_97.htm (OS-12CV-RX)
http://www.os-engines.co.jp/line_up/engine/car/catalog/11943.htm      (OS-18TZ-TX)
http://www.os-engines.co.jp/line_up/engine/car/catalog/11840.htm      (OS-18CV-RX)

http://www.hpi-europe.com/options.php?lang=en&type=engine  (HPI Engines)

Just for your information