RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Quetion about F-103 TRG wheel tire [打印本頁]

作者: carlos.fu 時間: 2008-10-20 15:16
標題: Quetion about F-103 TRG wheel tire
Dear Expert:

I hope you can answer me this quetion la.
IN F-103 RM, i can't change the real tire (right side face at the back of the car) the spur gear will loose if i change a rubber wheel of TRG.

How can i fix it?
Hope all the expert can help me on this la.
Thanks you so much.

作者: ccc_78 時間: 2008-10-20 15:27
你係唔係講珠叉果份嘢呀??
原裝星星要裝係條軨入面果set彈介???

[ 本帖最後由 ccc_78 於 2008-10-20 15:28 編輯 ]

作者: kwok7660 時間: 2008-10-20 15:31
係咪壓力啤鈴o果份野重係條舊呔入面, 重未拆出來裝落新呔度呀?

作者: pliablewai 時間: 2008-10-20 16:50
睇黎都似喇，壓力啤鈴果份野次次換呔都要拎番出黎架
不過我又掉番轉，問題係頭呔，上實哂都有成3mm虛位，你地有無試過

作者: gary 時間: 2008-10-20 17:10

原帖由 pliablewai 於 2008-10-20 16:50 發表

 登錄/註冊後可看大圖

睇黎都似喇，壓力啤鈴果份野次次換呔都要拎番出黎架
不過我又掉番轉，問題係頭呔，上實哂都有成3mm虛位，你地有無試過

落介子啦,但落左都係有虛位,不過會小D,
死症,係條鈴既問題~~

[ 本帖最後由 gary 於 2008-10-20 17:11 編輯 ]

作者: carlos.fu 時間: 2008-10-20 17:15
Yes, it was the bearing in the bal diff area.
I knew need to put that thing in the wheel, but TRG rubber tire wheel, dont have that place to put it in.

So that's why there not tight up lo.
As Pliablewai said, there will be 3mm or more.

Is that any way to fix it? or there are some part needs to be change?

作者: ccc_78 時間: 2008-10-20 21:06

原帖由 carlos.fu 於 2008-10-20 05:15 PM 發表

 登錄/註冊後可看大圖

Yes, it was the bearing in the bal diff area.
I knew need to put that thing in the wheel, but TRG rubber tire wheel, dont have that place to put it in.
So that's why there not tight up lo.
As Pl ...

全部裝係出面就ok

頭轆我就無3mm咁鬆,但我都有加介子就好好多

[ 本帖最後由 ccc_78 於 2008-10-20 21:08 編輯 ]

作者: carlos.fu 時間: 2008-10-21 19:05
OK Thanks all.

作者: RC 時間: 2008-10-21 23:13

原帖由 carlos.fu 於 2008-10-20 15:16 發表

 登錄/註冊後可看大圖

Dear Expert:

I hope you can answer me this quetion la.
IN F-103 RM, i can't change the real tire (right side face at the back of the car) the spur gear will loose if i change a rubber wheel of TRG ...

Front RUBBER tire, rear FOAM tire????? & add the back plate is this run become stable?????

[ 本帖最後由 RC 於 2008-10-21 23:19 編輯 ]

作者: pliablewai 時間: 2008-10-22 04:49
哈，其實無3mm咁多，攝番0.7mm倒啦，而家好好多喇

作者: carlos.fu 時間: 2008-10-22 14:59
Really? Let me try try sin.
Thanks all expert.
I found out that those bearing must put in the outside of the TRG wheel. There is different with the Tamiya wheel.
Also would like to ask if there are any one playing GTR Evolution (WTCC) pc game?
Im also a gamer on this. Use to play F3000.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)