RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 緊急入泥幫幫我不能撻車 [打印本頁]

作者: ~日本鋒晴畫~    時間: 2007-12-23 10:23
標題: 緊急入泥幫幫我不能撻車
事件:不能撻車
情況:第一次撻車後,兩三日後撻撻唔到,但係我以經set好哂d野,大針細針都係兩圈平,有足夠生風(有1/3了)火咀無燒,條喉積左d油我都清埋但係都撻唔番=.="我用06副計
請問各c兄有咩方法解決,謝謝
作者: chungtsai    時間: 2007-12-23 10:41
標題: 回復 1# 的帖子
咁有冇check 過入油未?
作者: ~日本鋒晴畫~    時間: 2007-12-23 10:45
原帖由 chungtsai 於 2007-12-23 10:41 發表
咁有冇check 過入油未?

入左啦=.=!!
作者: feel14    時間: 2007-12-23 10:51
火咀電冇電
作者: ~日本鋒晴畫~    時間: 2007-12-23 10:57
原帖由 feel14 於 2007-12-23 10:51 發表
火咀電冇電

有試左
折左出泥睇,火咀插左火咀電之後係紅左,但會唔會唔夠紅?
作者: feel14    時間: 2007-12-23 10:59
都可能會既,  不過機會唔大

雖然你入左油, 但你知唔知上唔上到油? 油喉 同 化油氣 你見唔見到有油到?
作者: ~日本鋒晴畫~    時間: 2007-12-23 11:01
原帖由 feel14 於 2007-12-23 10:59 發表
都可能會既,  不過機會唔大

雖然你入左油, 但你知唔知上唔上到油? 油喉 同 化油氣 你見唔見到有油到?

油喉有油但係化油氣就見唔到有(係唔係入生風個位到睇?)
作者: yman    時間: 2007-12-23 11:12
this is normal, becaue there has some oil inside your engine, just take away glow plug, pump out the
oil inside the engine, clean the oil around the head, install the glow plug then start again your engine
作者: ~日本鋒晴畫~    時間: 2007-12-23 11:20
原帖由 yman 於 2007-12-23 11:12 發表
this is normal, becaue there has some oil inside your engine, just take away glow plug, pump out the
oil inside the engine, clean the oil around the head, install the glow plug then start again your  ...

姐係要打散泥洗?我折過火咀泥睇,活塞沒有太多油,好似好正常禁,壓縮正常,手拉一下條喉有氣出
作者: feel14    時間: 2007-12-23 11:24
你試下拆左粒火咀, 拉下個手拉, 睇下有冇油響機頂射出黎.....

正常係有既
作者: ~日本鋒晴畫~    時間: 2007-12-23 12:02
原帖由 feel14 於 2007-12-23 11:24 發表
你試下拆左粒火咀, 拉下個手拉, 睇下有冇油響機頂射出黎.....

正常係有既

各位c兄我搵到個原因啦~
我e家撻得著車,但係架車好似唔識回壓禁,一用完o個啖油就死火(我禁住出氣個位,緊住拉手拉等d油去到化油器,跟住插火咀電撻,撻到,但跟住就好似唔識回壓,d油唔識自己去化油器到,當一用完頭先泵洛化油d油就死火)
e個情況應該點搞?
無油到?我機頂無油飛出泥...
作者: ~日本鋒晴畫~    時間: 2007-12-23 12:20
c兄幫幫手~唔該
作者: feel14    時間: 2007-12-23 12:36
俾油之後死火 or 就咁著完車一陣就死?
作者: ~日本鋒晴畫~    時間: 2007-12-23 12:41
原帖由 feel14 於 2007-12-23 12:36 發表
俾油之後死火 or 就咁著完車一陣就死?

就咁著完車一陣就死,姐係好似用完用手拉拉入去d油,緊住死火,d油唔識自己郁,係條喉到=.=
作者: feel14    時間: 2007-12-23 13:03
咁有冇試過俾油?

你要自己睇下係 多油過頭 or 唔夠油 導致死火

如果你話冇油到既話, 你試下鬆少少油針再試過
作者: ~日本鋒晴畫~    時間: 2007-12-23 13:04
http://hk.youtube.com/watch?v=JpdjfPUZ-JI
有片睇....

[ 本帖最後由 ~日本鋒晴畫~ 於 2007-12-23 13:05 編輯 ]
作者: feel14    時間: 2007-12-23 13:29
你試下響個控度set佢俾少少油先, 再去撻車

or 撻左車之後, 俾幾下油試下
作者: ~日本鋒晴畫~    時間: 2007-12-23 13:39
原帖由 feel14 於 2007-12-23 13:29 發表
你試下響個控度set佢俾少少油先, 再去撻車

or 撻左車之後, 俾幾下油試下

e家個情況又變左=.=
set大左個油門,一囉開火咀電就死火,但係我插左火咀電誠分鍾,引擎都熱埋一囉開火咀電就死火
作者: ~日本鋒晴畫~    時間: 2007-12-23 13:40
同埋比油都死火
作者: feel14    時間: 2007-12-23 13:53
較細返支油針....扭緊佢, 續d續d試
作者: ~日本鋒晴畫~    時間: 2007-12-23 13:53
較極都著唔到好灰......明明咩都set岩哂
作者: feel14    時間: 2007-12-23 14:10
慢慢黎, set返好有排你玩.....
作者: JonnyC    時間: 2007-12-24 01:02
清洗引擎及死氣喉試下??!!
作者: chrishkyung    時間: 2007-12-24 14:18
your 油針 is too rich or u get too many fuel inside the engine

BTW, when u start the engine, push some throttle to burn the remaining fuel inside the engine case and warm up the engine to suitable temperature...


if u can, please post some photos about your engine
作者: tselip    時間: 2007-12-24 18:16
其實油針無話收幾多圈失叫標準...
部部出廠唔同.....
作者: ~日本鋒晴畫~    時間: 2007-12-24 21:55
原帖由 chrishkyung 於 2007-12-24 14:18 發表
your 油針 is too rich or u get too many fuel inside the engine

BTW, when u start the engine, push some throttle to burn the remaining fuel inside the engine case and warm up the engine to suitable  ...

你睇下我條片先啦=.=個情況就係禁......
http://hk.youtube.com/watch?v=JpdjfPUZ-JI
作者: IBM    時間: 2007-12-25 02:25
睇過你條片, 聽聲應該是  too rich 太副油,
試下撻著之後拿拿聲比幾下油, 直至汽缸內的油燒去, 聲音變得清脆,
然後收油睇下會唔會死火.

都唔得, 就試下咁樣調較:

先把大油針 set 番去2圈半的出廠位置,
然後把細油針逐少逐少順時針方向擰入

每次只擰入約五分鐘(30度), 撻車試下,
唔得, 再擰入30度, 再撻, 再試, 再擰30度, 再試.

到成功後,架車可以運轉正常後, 先再較大油針.

希望可以幫到你.
作者: f60    時間: 2007-12-25 19:34
著左車快,即刻拿起支搖控比油,唔好一下比盡,慢慢比咁比,等佢燒左d油就得架啦.
再較細小小大油針就唔怕架啦.....
作者: chrishkyung    時間: 2007-12-25 22:40
before i offer advice to u, i of course have watched your video....

my knowledge in nitro engine is not very professional, but at least better than some people....
作者: ~日本鋒晴畫~    時間: 2007-12-27 16:25
原帖由 IBM 於 2007-12-25 02:25 發表
睇過你條片, 聽聲應該是  too rich 太副油,
試下撻著之後拿拿聲比幾下油, 直至汽缸內的油燒去, 聲音變得清脆,
然後收油睇下會唔會死火.

都唔得, 就試下咁樣調較:

先把大油針 set 番去2圈半的出廠位置,
然 ...

試左,唔得=,=,其實會唔會係曲續果個位積油大多?如果係禁洗唔洗打散泥清?
作者: chrishkyung    時間: 2007-12-27 16:38
u can try another new glow plug....maybe the problem of the glow plug....buy an OS A5 glow plug to try

By the way, based on "曲續果個位積油大多" and your video, your 油針 is too rich...
clockwise your 油針 approx half round to try again....if u can make a video record, please also take some shot on your 油針 and its componets

GXR15 is a very easy engine.....
作者: ~日本鋒晴畫~    時間: 2007-12-27 16:42
岩岩試左,又得左啦ro ,但係怠速太快
作者: ~日本鋒晴畫~    時間: 2007-12-27 16:45
e d野真係要自己摸好難教
作者: piccoengine    時間: 2007-12-27 16:57
原帖由 ~日本鋒晴畫~ 於 2007-12-27 16:45 發表
e d野真係要自己摸好難教

但係自己摸返泥會更加入腦....
作者: piccoengine    時間: 2007-12-27 16:58
原帖由 ~日本鋒晴畫~ 於 2007-12-27 16:45 發表
e d野真係要自己摸好難教

有時人地講完野會轉頭就唔記得....
作者: stanley7191    時間: 2008-1-21 00:43
標題: 回復 18# 的帖子
you try change 火咀




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/) Powered by Discuz! X3.2