RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Step by Step: lower ride height using DIY rear toe-in link [打印本頁]

作者: billy86che 時間: 2007-11-17 15:01
標題: Step by Step: lower ride height using DIY rear toe-in link
Step by step to get a lower ride height and better clearance for the AWD:

作者: billy86che 時間: 2007-11-17 15:09
These pictures show Part 2:

作者: billy86che 時間: 2007-11-17 15:14
I'll give this to 偉哥 and will make the last one for Dick dick Jai because I promised them. No one else will be entertained then. The rest of you have to DO IT YOURSELF!!!!!

[ 本帖最後由 billy86che 於 2007-11-17 15:34 編輯 ]

作者: rk2 時間: 2007-11-17 16:42
好有心機

作者: 800mah 時間: 2007-11-17 19:51
my AWD isn't with me right now
but i don't quite understand what's the purpse of "remove some plastic as shown" in the3rd photo

作者: billy86che 時間: 2007-11-17 21:38

原帖由 800mah 於 2007-11-17 19:51 發表

 登錄/註冊後可看大圖

my AWD isn't with me right now
but i don't quite understand what's the purpse of "remove some plastic as shown" in the3rd photo

Compare the original (left) with the modified one (right).
Only by doing this can I later remove the toe in link.

[ 本帖最後由 billy86che 於 2007-11-17 22:01 編輯 ]

作者: henry888 時間: 2007-11-18 01:37
今日見到偉哥, 牙擦擦咁啦

不過真係好有用, 起碼low低多1-2mm
又乾淨好多

作者: billy86che 時間: 2007-11-18 08:41

原帖由 henry888 於 2007-11-18 01:37 發表

 登錄/註冊後可看大圖

今日見到偉哥, 牙擦擦咁啦
不過真係好有用, 起碼low低多1-2mm
又乾淨好多

Don't tell him that there is still something to be done before he can maximize the use of the DIY.

作者: haihe 時間: 2007-11-18 11:17
那么怎么更换后胎尺呢?

作者: billy86che 時間: 2007-11-18 19:28

原帖由 haihe 於 2007-11-18 11:17 發表

 登錄/註冊後可看大圖

那么怎么更换后胎尺呢?

You have to think more carefully and read more carefully the captions of the pictures.

作者: 椰禮 時間: 2007-11-18 19:59
我想問本身舊野有咩用既呢??

作者: billy86che 時間: 2007-11-18 20:05

原帖由椰禮於 2007-11-18 19:59 發表

 登錄/註冊後可看大圖

我想問本身舊野有咩用既呢??

lower ride height and better clearance.

作者: 椰禮 時間: 2007-11-18 20:26
我指未改之前姐係係車架上有咩作動??

作者: billy86che 時間: 2007-11-18 21:30

原帖由椰禮於 2007-11-18 20:26 發表

 登錄/註冊後可看大圖

我指未改之前姐係係車架上有咩作動??

Sorry, I couldn't follow. Did you mean what was wrong with the original parts?
原本凸出黎,唔夠平,易high地.

[ 本帖最後由 billy86che 於 2007-11-18 22:28 編輯 ]

作者: 偉記 時間: 2007-11-18 23:12
標題: 回復 3# 的帖子
唔該老師,好正,等我又試下整條C比架(90)用

作者: 偉記 時間: 2007-11-18 23:17
標題: 回復 13# 的帖子
係尾轆呔尺,控制尾轆toe in ,
toe in 少D 就轉多D
toe in 多D尾定D

作者: checkie 時間: 2007-11-19 06:11
nice job

作者: Colin 時間: 2007-11-19 12:35
this is reinforcement part 1.
o個到加兩個黑色小片目的係咩呀?其實係咪應該可以唔洗加?

作者: billy86che 時間: 2007-11-19 16:19

原帖由 Colin 於 2007-11-19 12:35 發表

 登錄/註冊後可看大圖

this is reinforcement part 1.
o個到加兩個黑色小片目的係咩呀?其實係咪應該可以唔洗加?

You can try it by yourself.

作者: billy86che 時間: 2007-11-19 16:21

原帖由 Colin 於 2007-11-19 12:35 發表

 登錄/註冊後可看大圖

this is reinforcement part 1.
o個到加兩個黑色小片目的係咩呀?其實係咪應該可以唔洗加?

You can try it by yourself. (Let me remind you that I won't be using any screw at the bottom and the toe-in link is very thin after filing)

作者: sumandy 時間: 2007-11-19 16:46

原帖由 billy86che 於 2007-11-19 16:21 發表

 登錄/註冊後可看大圖

You can try it by yourself. (Let me remind you that I won't be using any screw at the bottom and the toe-in link is very thin after filing)

toe-in link is very thin after filing... easy break?

作者: billy86che 時間: 2007-11-19 16:51

原帖由 sumandy 於 2007-11-19 16:46 發表

 登錄/註冊後可看大圖

toe-in link is very thin after filing... easy break?

If you have added the reinforcement as shown , you can even go further to remove the middle part of the toe-in link to achieve an even better clearance and remove the upper part (the handle) of the bumper to make it lighter.

作者: penny. 時間: 2007-11-20 18:26
喎！真正勁！！老師你係勁！！！

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)