RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: micro t電變最高可以去到幾volt? [打印本頁]

作者: WallaceNg 時間: 2007-11-14 11:06
標題: micro t電變最高可以去到幾volt?
想買部micro t，但係micro t個電變最高可以去到幾volt?

作者: billy86che 時間: 2007-11-14 11:14

原帖由 WallaceNg 於 2007-11-14 11:06 發表

 登錄/註冊後可看大圖

想買部micro t，但係micro t個電變最高可以去到幾volt?

想換電?

作者: WallaceNg 時間: 2007-11-14 11:17
yes，唔知點改好

作者: Justhandguns 時間: 2007-11-26 21:22
Using 7.4 Lipo, so far so good.

作者: Triton 時間: 2007-11-26 21:42
咁mini-z 的am pcb最高可以去到幾volt?
THX!!

作者: billy86che 時間: 2007-11-26 21:55

原帖由 Triton 於 2007-11-26 21:42 發表

 登錄/註冊後可看大圖

咁mini-z 的am pcb最高可以去到幾volt?
THX!!

6V because one cap. indicates it tolerates up to that voltage.

作者: Triton 時間: 2007-11-26 22:16
Using 7.4 Lipo ok?

作者: billy86che 時間: 2007-11-26 23:09

原帖由 Triton 於 2007-11-26 22:16 發表

 登錄/註冊後可看大圖

Using 7.4 Lipo ok?

No, you'll get the cap burnt unless you replace it with something that tolerates a higher voltage such as a 47u 10v.

作者: Triton 時間: 2007-11-27 00:18
OK....THX!!

作者: 0433351410 時間: 2007-11-27 01:10
I was already try to use the 7.4v Lipo it is so fast

but is hard to fit in the car (still thinking)

作者: billy86che 時間: 2007-11-27 07:14

原帖由 0433351410 於 2007-11-27 01:10 發表

 登錄/註冊後可看大圖

I was already try to use the 7.4v Lipo it is so fast but is hard to fit in the car (still thinking)

It certainly takes some time and effort.

作者: 0433351410 時間: 2007-11-27 10:50
may i know what side Lipo every one using because i think my Lipo is a bit big (68X33X17mm)

作者: billy86che 時間: 2007-11-27 11:14

原帖由 0433351410 於 2007-11-27 10:50 發表

 登錄/註冊後可看大圖

may i know what side Lipo every one using because i think my Lipo is a bit big (68X33X17mm)

It is a bit troublesome because you need either to modify the chassis to give room to the cells or you can buy smaller cells that have a lower capacity.

See the picture on the left? You can see I put the lipo (silver in colour)at the bottom of the chassis.

作者: teamlosi 時間: 2007-11-27 12:22

原帖由 billy86che 於 2007-11-27 11:14 發表

 登錄/註冊後可看大圖

It is a bit troublesome because you need either to modify the chassis to give room to the cells or you can buy smaller cells that have a lower capacity.

See the picture on the left? You can see ...

如果攞電池位頂部將電打棟放是可以的,但只可用薄裝7.4.

作者: billy86che 時間: 2007-11-27 12:46

原帖由 teamlosi 於 2007-11-27 12:22 發表

 登錄/註冊後可看大圖

如果攞電池位頂部將電打棟放是可以的,但只可用薄裝7.4.

攞電池位頂部??? 真難理解.

作者: teamlosi 時間: 2007-11-27 13:43

原帖由 billy86che 於 2007-11-27 12:46 發表

 登錄/註冊後可看大圖

攞電池位頂部??? 真難理解.

我意思是車架擺電池位的頂部,即天線位置下！

作者: billy86che 時間: 2007-11-27 15:33

原帖由 teamlosi 於 2007-11-27 13:43 發表

 登錄/註冊後可看大圖

我意思是車架擺電池位的頂部,即天線位置下！

OK. But is it better or worse?

作者: Triton 時間: 2007-11-27 18:48

原帖由 0433351410 於 2007-11-27 01:10 發表

 登錄/註冊後可看大圖

I was already try to use the 7.4v Lipo it is so fast but is hard to fit in the car (still thinking)

又話唔用我7.4v Lipo o既???

作者: 0433351410 時間: 2007-11-27 20:27

原帖由 Triton 於 2007-11-27 18:48 發表

 登錄/註冊後可看大圖

又話唔用我7.4v Lipo o既???

Do i know u???

作者: billy86che 時間: 2007-11-28 10:54
Unlike what a lot of people may think, I use the lipo not because I want a higher voltage, but to achieve a lower CG.

作者: billy86che 時間: 2007-11-28 10:55
Unlike what a lot of people may think, I use the lipo not because I want a higher voltage, but to achieve a lower CG. I could then go faster during corners.

Unfortunately, they notice only my speed at the straight. Come on,that's only the by-product!

[ 本帖最後由 billy86che 於 2007-11-28 10:58 編輯 ]

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)