RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: problem with Lunch Box (Solved!) [打印本頁]

作者: 800mah 時間: 2007-10-29 23:23
標題: problem with Lunch Box (Solved!)
Solved~! i moved the servo a bit and spent $2x to replaced the steering rods. now the steering mechanism becomes symmetrcial

hey brothers, i have a question about the lunch box
as the axle of steering servo is not placed in the middle of the car,
as u can see the steering rods are of different length.
it creats a porblem that the steering response/angles on the left and right sides are not symmetrical.

any brothers have suggestions on how to solve it?

[ 本帖最後由 800mah 於 2007-10-31 22:21 編輯 ]

作者: Brushless 時間: 2007-10-29 23:33
玩Lunch Box智在爽吓，design比較簡單，睇怕都好難改善囉。

作者: gibson 時間: 2007-10-29 23:42
Who cares!!

作者: 800mah 時間: 2007-10-29 23:51
but i find it very annoying.

will try to solve the problem later this week, just need to position the servo in the middle and get two steering rods of the same length

作者: faifai52 時間: 2007-10-29 23:52

i think these c hings are right, it just doesn't matter the alignment of the LB is. HAVE FUN

作者: 觀星是答案 時間: 2007-10-29 23:52
架車個 design 係 1987 年 wo
當年有好多車都係長短推杆架啦

http://www.tamiyausa.com/product/item.php?product-id=58346

唔好要求 o甘多啦
你睇下架車, 頭擔連上搖臂都無, 又唔係獨立避震
就知架車只係 for fun 架啦

作者: Brushless 時間: 2007-10-30 01:07
標題: 回復 4# 的帖子
Just have fun，永遠着住衫玩離遠望，唔好除衫近距離研究啦

作者: mikewu 時間: 2007-10-30 19:06
Brother Davis, it's hard enough to find replacement steering rod for LB already. I seriously doubt that even you have fix the problem, your LB is going to handle better.... As the rest of the brother says, just put it together and have fun in stock form.....
Sorry to disappoint you....

作者: agentjerry 時間: 2007-10-30 19:25
it is a RC for fun not for run

作者: 800mah 時間: 2007-10-30 21:44

原帖由 mikewu 於 2007-10-30 19:06 發表

 登錄/註冊後可看大圖

Brother Davis, it's hard enough to find replacement steering rod for LB already. I seriously doubt that even you have fix the problem, your LB is going to handle better.... As the rest of the brothe ...

thanks mike, but i'll just try to get rods of similar length ...from GPM maybe.

and positioning the servo in the middle should not be a big problem.

作者: 800mah 時間: 2007-10-31 22:22
hey guys, i've sorted out the 'problem'

作者: Brushless 時間: 2007-10-31 22:28
咁落力，恭喜晒.....................只要有恆心，鐵柱more成針

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)