RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 想自制1比10貼紙 [打印本頁]

作者: Buildinglung 時間: 2007-9-24 18:32
標題: 想自制1比10貼紙
我公司有部彩色Lazer Printer,想試下自已Print 貼紙

！唔知通常用邊個Software整既呢??

大約流程係點??另外物料又點搵呢??重有係唔係做唔倒白色字架??
請各位師兄指教指教

！

作者: Buildinglung 時間: 2007-9-24 22:54
無人肯教???

作者: 長崎良尾 時間: 2007-9-24 23:23

朋友唔係你想像中咁蕳單.......

作者: Buildinglung 時間: 2007-9-25 01:04

原帖由 長崎良尾 於 2007-9-24 23:23 發表

 登錄/註冊後可看大圖

朋友唔係你想像中咁蕳單.......

我都話想試下lor.....所以咪想知law.師兄....

簡單就唔洗請教各位大大,我自己閉門做""車""啦......

指點下丫！

[ 本帖最後由 Buildinglung 於 2007-9-25 01:10 編輯 ]

作者: lespaul 時間: 2007-9-25 01:10
First of all, you need to print a white colour, than print the pattern on top.

The white colour is to block the sticker to make it a non-transparent sticker. I hope you understand la!! Thats why its not easy!!

作者: Administrator 時間: 2007-9-25 01:17
you'll need to get the Gloss decal sticker paper. (Don't use the Matt 1's because the surface will be rough). they both come in transparent or white sheet. (so if u need to have white letter, print the border out....

)

Now, finding these paper will be a bit of a problem...

you will have to try ur luck on the professional printing suppliers....

作者: Buildinglung 時間: 2007-9-25 01:20
哦! 我重唸住用全透明就得tim(因為我print 水貼都係全透明)....!如果本身我已經用白底膠貼呢???

作者: Buildinglung 時間: 2007-9-25 01:25

原帖由 Administrator 於 2007-9-25 01:17 發表

 登錄/註冊後可看大圖

you'll need to get the Gloss decal sticker paper. (Don't use the Matt 1's because the surface will be rough). they both come in transparent or white sheet. (so if u need to have white letter, print th ...

as you mean, the white letter need cut it out ,can't print it out?? i got the gloss decal sticker paper already..... as you mean, i can direct print it out on the sticker paper, if there are no white clour in the picture???

作者: Administrator 時間: 2007-9-25 02:43
if your laser printer can print "White" ( which i highly doubted.) you can try to print it on the transparent sheet. Normally if the design doesn't need white color. i'll just print it out as it is.

White gloss sticker sheet are used if you got something that has a white background (because its not possible to print white in printer.) just print the outline of the design. and cut it out after printing.

Good luck with your printing. but through my experience, you'll have to do this quite a few times to get the size (and color) correct.

作者: Buildinglung 時間: 2007-9-25 02:56

原帖由 Administrator 於 2007-9-25 02:43 發表

 登錄/註冊後可看大圖

if your laser printer can print "White" ( which i highly doubted.) you can try to print it on the transparent sheet. Normally if the design doesn't need white color. i'll just print it out as it is.
...

Actually i would like to make some small logo first..... so, i think i can do that.
one more question, which software more suitable for making that kind of sticker....

作者: Administrator 時間: 2007-9-25 03:29
theres not a specific software that i can suggest. but i used paint shop pro.
as long as the software can do some decent graphic work (MS Paint will NOT recommend

) then you should be fine.

作者: gegegum 時間: 2007-9-25 11:40

原帖由 長崎良尾 於 2007-9-24 11:23 PM 發表

 登錄/註冊後可看大圖

朋友唔係你想像中咁單.......

真係好難架!

同埋你留意o下你買o既貼紙, 通常都唔係好"痴", 又冇彈性, 曲面一定唔得, 小心!

作者: Buildinglung 時間: 2007-9-25 13:33

原帖由 gegegum 於 2007-9-25 11:40 發表

 登錄/註冊後可看大圖

真係好難架!
同埋你留意o下你買o既貼紙, 通常都唔係好"痴", 又冇彈性, 曲面一定唔得, 小心!

i will start with some small logo first

....... i will try,,,

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)