RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: my GXR-15 ar [打印本頁]

作者: Eric_116 時間: 2007-8-6 09:03
標題: my GXR-15 ar
oh the wire is broken so need to change engine ar

can anyone tell me which engine is good ar and what other parts i need also $$. Thank you

作者: valklai 時間: 2007-8-6 09:49
Ha brother,
U no need to change another engine.
U just need to replace a new hand pull starter that it.

作者: Eric_116 時間: 2007-8-6 09:52

原帖由 valklai 於 2007-8-6 09:49 AM 發表

 登錄/註冊後可看大圖

Ha brother,
U no need to change another engine.
U just need to replace a new hand pull starter that it.

Yes u are right but i want to change the engine long time ago so i think is time to change it. Thank you

作者: RGM-111 時間: 2007-8-7 01:44
Eric兄 ...爛手拉 ...唔洗..換..Engine wor...換過條繩未ok law,.....不過你都成日想換Engine

要手拉平,靚正.. OS 12-TG(P)X 啦 ($10xx)
手拉, 後排機, 又用到3D clutch...不過你要買過條曲($1xx),成set 3D clutch($4xx) 先用得=_=...expensive過部05T+

P.S. 你D 藍色...shock stay & center bulk ....係唔係 "五金舖" (剪哎)....買的

作者: Eric_116 時間: 2007-8-7 02:27

原帖由 RGM-111 於 2007-8-7 01:44 AM 發表

 登錄/註冊後可看大圖

Eric兄 ...爛手拉 ...唔洗..換..Engine wor...換過條繩未ok law,.....不過你都成日想換Engine

要手拉平,靚正.. OS 12-TG(P)X 啦 ($10xx)
手拉, 後排機, 又用到3D clutch...不過你要買過條曲($1 ...

Thank you for your infomation what about no 手拉 engine ar. Thank you

If i buy the OS-12-TG(P)X which manifold i can use for OS engine b/c i want to keep the JPL muffler, what is 條曲 and can i use this clutch ar(http://www.amainhobbies.com/product_info.php/cPath/1_23_78/products_id/7941) also can i use kyosho (VSW-059) 個粒2speed Nut. Which flywheel i can use for this OS engine. Thank you

P.S. 你D 藍色...shock stay & center bulk ....係唔係 "五金舖" (剪哎)....買的---(bought it from some body)

[ 本帖最後由 Eric_116 於 2007-8-7 03:11 編輯 ]

作者: RGM-111 時間: 2007-8-8 01:53
標題: 回復 #5 Eric_116 的帖子
No 手拉 OS 12TZ 3 or 5 port 正,平 .12class ~1.5Ps

if use OS-12-tG(P)x ..you can keep your JPL muffler, just buy the 後排("mainfold" = 曲)
your quoted clutch is for off-road , better buy kyosho 3D clutch set...if using OS-12-TG(P)/TZ due to they are SG Pilot Sharft..no need to use the kyosho(VSW-059) 2 speed nuts & flywheel....because the 3D clutch kit had all you need, just buy the 1st & 2nd pinon gears ...^-^

作者: Eric_116 時間: 2007-8-8 23:31

原帖由 RGM-111 於 2007-8-8 01:53 AM 發表

 登錄/註冊後可看大圖

No 手拉 OS 12TZ 3 or 5 port 正,平 .12class ~1.5Ps

if use OS-12-tG(P)x ..you can keep your JPL muffler, just buy the 後排("mainfold" = 曲)
your quoted clutch is for off-road , better buy kyos ...

Thank you for your information i just bought the OS-12-tG(P)x and i will buy the Kyosho 3D clutch kit

Do u know any good mainfold i can buy ar and which engine mount i need to buy ar.

TThank you

[ 本帖最後由 Eric_116 於 2007-8-9 00:23 編輯 ]

作者: RGM-111 時間: 2007-8-9 01:31
標題: 回復 #7 Eric_116 的帖子
when buy the 3D clutch kit , don't forget to buy the 1st & 2nd pinon gears

HEC/JPL 後排mainfold is good ...also can match with your muffler.....then you can using both 後排&側排Engine

go to buy a High Mount Engine Mount(for Hand Pull Starter) ....just ask the shop keeper.....they will help you ^_^....
Go fast and enjoy your new Engine

:lol

作者: coronafans 時間: 2007-8-11 00:17
買個set手拉咪得, about$90

作者: powis 時間: 2007-8-13 00:41
how the OS-12-tG(P)x performance compare with the original Kyosho GXR-15 and OS 12TZ 3port???

作者: Eric_116 時間: 2007-8-13 00:52

原帖由 powis 於 2007-8-13 12:41 AM 發表

 登錄/註冊後可看大圖

how the OS-12-tG(P)x performance compare with the original Kyosho GXR-15 and OS 12TZ 3port???

I haven't put it ar b/c i still thinking which muffler is good ar can u give me some idea JPL & K Factory you can see the picture in my other post. Thank you

[ 本帖最後由 Eric_116 於 2007-8-13 00:53 編輯 ]

作者: Eric_116 時間: 2007-8-15 13:27
finally erverthng is finish OS-12-tG(P)x, Kyosho 3D clutch and K Factory exhaust

but no more $$

[ 本帖最後由 Eric_116 於 2007-8-15 13:28 編輯 ]

作者: chrishkyung 時間: 2007-8-15 18:08
hope it will be faster than your previous GXR15 engine

作者: powis 時間: 2007-8-16 00:06
Please let us know how the new engine performance compare with GXR15!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)