RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Another shell for CC01 [打印本頁]

作者: gibson 時間: 2007-5-1 22:45
標題: Another shell for CC01
After a test run, confirmed its good fit for CC01. The wheel base almost the same...

登錄/註冊後可看大圖

作者: J 時間: 2007-5-1 22:47
where can I buy this shell lei Gibson?? is it pre-painted? It fits CC01 SWB (pajero) wheelbase right?

作者: mikewu 時間: 2007-5-1 22:48
beautiful.... You should have seen my MU after Sunday run...... Ever heard of "Lo Lai"?? "Mix mud"?

Brother UHU, please show brother Gibson my MU if you can.....

作者: gibson 時間: 2007-5-1 22:51

原帖由 J 於 2007-5-1 22:47 發表
where can I buy this shell lei Gibson?? is it pre-painted? It fits CC01 SWB (pajero) wheelbase right?

Yes, pajero wheelbase, the shell from chi lok at HKD90..... sometimes out of stock!!
Too bad its pre-painted, with two colour theme, one is the above, the other is forrest-red theme... also not bad!!!!!

作者: gibson 時間: 2007-5-1 22:53

原帖由 mikewu 於 2007-5-1 22:48 發表
beautiful.... You should have seen my MU after Sunday run...... Ever heard of "Lo Lai"?? "Mix mud"? Brother UHU, please show brother Gibson my MU if you can.....

Only two photoes...... too bad, I missed the event, next time la, quick quick blow chicken again la!!!

作者: J 時間: 2007-5-1 22:56

原帖由 gibson 於 2007-5-1 22:51 發表

Yes, pajero wheelbase, the shell from chi lok at HKD90..... sometimes out of stock!!
Too bad its pre-painted, with two colour theme, one is the above, the other is forrest-red theme... a ...

not bad not bad... i may try the $90 one and restore my pajero hard shell

作者: gibson 時間: 2007-5-1 22:59
Now I can run my CC01 and keep the pajero shell at home!!

作者: J 時間: 2007-5-1 23:03
I got the touareg body, hoping to use it for 'rough play' but then i guess i need the longer centre drive axle to make it the right WB

anyone knows any chance to get the longer axle?

作者: mikewu 時間: 2007-5-1 23:05

原帖由 J 於 2007-5-1 23:03 發表
I got the touareg body, hoping to use it for 'rough play' but then i guess i need the longer centre drive axle to make it the right WB
anyone knows any chance to get the longer axle?

Brother J, can you take a trip to brother HUH's house and steal his camera??

作者: J 時間: 2007-5-1 23:09
just talked to him on phone.....he is soft'ing with his gf arrrr...

作者: courel500 時間: 2007-5-1 23:10
唉......仲要等幾耐先有相睇呀 !

作者: orange00 時間: 2007-5-1 23:11

登錄/註冊後可看大圖

how about this one?

作者: gibson 時間: 2007-5-1 23:12

原帖由 mikewu 於 2007-5-1 23:05 發表

Brother J, can you take a trip to brother HUH's house and steal his camera??

Good, go ahead, force open..... like the SWAT!!

作者: J 時間: 2007-5-1 23:13

原帖由 orange00 於 2007-5-1 23:11 發表

登錄/註冊後可看大圖

how about this one?

damm it... so nice!! tell us details pls!~

作者: gibson 時間: 2007-5-1 23:14

原帖由 orange00 於 2007-5-1 23:11 發表

登錄/註冊後可看大圖

how about this one?

WWWWWWWWaaaaaaaa,,,,,, MUD LEI GA, so beautiful!!!!!! Not for running bor!!!!

作者: orange00 時間: 2007-5-1 23:17
Mainland Toy with official license FJ Cruiser. Main point is....RMB99. Cheap Cheap solution.

登錄/註冊後可看大圖

[ 本帖最後由 orange00 於 2007-5-1 23:21 編輯 ]

作者: mikewu 時間: 2007-5-2 09:58
Brother orange... I bought the same shell from Yahoo for $99 and ready to put on the TLT..
It's a Toyota FJ which supposed to be the retro version of the Legendary FJ40 truck... Unfortunately they only makes LHD and buying it in mainland cost well over $600k RMB!

作者: orange00 時間: 2007-5-2 15:48

原帖由 mikewu 於 2007-5-2 09:58 發表
$600k RMB

唔係呱

作者: mikewu 時間: 2007-5-2 16:03

原帖由 orange00 於 2007-5-2 15:48 發表

唔係呱

Oh... yes... one of my supplier got one in yellow and I think that's how much they pay for it... It's imported from the US (made in Japan)....

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)