RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: AWD 彈弓一問 [打印本頁]

作者: tonytjia@zone 時間: 2007-3-30 00:40
標題: AWD 彈弓一問
有無人用京商出的AWD彈弓？
好唔好？

作者: scalpel 時間: 2007-3-30 00:42

原帖由 tonytjia@zone 於 2007-3-30 00:40 發表
有無人用京商出的AWD彈弓？
好唔好？

Yes! I am using, the yellow one(hard)

作者: xlarge 時間: 2007-3-30 02:50

原帖由 tonytjia@zone 於 2007-3-30 00:40 發表
有無人用京商出的AWD彈弓？
好唔好？

都叫ok既........
不過要自己cut
有d麻煩
宜家當然係買PN好
唔洗cut又多度數

作者: tonytjia@zone 時間: 2007-3-30 14:37
標題: 回復 #3 xlarge 的帖子
I have PN spring when I use it my car lost control when I turn.
My setup is as following:

- Benz CKL Vodafone
- AD PCB no fet
- AD Stock motor
- 19/29 A2/B2
- PN Motor heat sink
- Front 1 Degree Camber, Rear 2 Degree Camber
- Front & Rear Atmoic ball diff.

Can you share how you set up your front and rear using PN spring?

作者: xlarge 時間: 2007-3-30 15:00

原帖由 tonytjia@zone 於 2007-3-30 14:37 發表
I have PN spring when I use it my car lost control when I turn.
My setup is as following:

- Benz CKL Vodafone
- AD PCB no fet
- AD Stock motor
- 19/29 A2/B2
- PN Motor heat sink
- Front 1 ...

你用咩o太

作者: tonytjia@zone 時間: 2007-3-30 20:22
標題: 回復 #5 xlarge 的帖子
I use atomic 20 degree no pattern front
rear atomic 10 degree with pattern

作者: ganboy 時間: 2007-3-30 22:11
do you apply tyre glue?
are your ball diff. set up properly?
which spring do you use in both front & rear?

To make your suspensions w/ PN spring work properly, you should add spacers(shims) on each knuckle, you may start with adding 0.8mm at bottom & 0.4mm on the top on each corner, and adjust the droop by adding and removing shims to suit your driving style but make sure not to preload springs...

If you dont add any shims under PN springs, the ride height of your AWD is certainly too low. Moreover, given the very large droop value, you car will be very responsive. this may refer to why you lose control when cornering.

What you need to buy is a set of 3mm shims a set of 4mm shims from PN, other brands may not fit into your knuckles.

enjoy your AWD!

作者: tonytjia@zone 時間: 2007-3-30 23:38
標題: 回復 #7 ganboy 的帖子
I used double tape to stick my tyre.

What colour of PN springs shall be apply in front and rear?
White front and Green at rear?

For the shims, 0.4mm on top of the spring? 0.8mm on the bottom of kucnkle?

作者: ganboy 時間: 2007-3-30 23:58
標題: 回復 #8 tonytjia@zone 的帖子
White front and Green at rear should be ok for stock car
0.4 below spring, 0.8 below knuckle

Ah..one more thing, apply #15000 kyosho gear diff grease on 4 joints between kunckles and upper cover.

作者: tonytjia@zone 時間: 2007-4-2 01:03
標題: 回復 #9 ganboy 的帖子
Thanks ganboy.

Finally I get the setting done and now is ok... even though not perfect...

I think I will go for SAS on my next stage.

For the shims, if I remove some from the bottom or below spring how will it affect the turning?

作者: ganboy 時間: 2007-4-2 10:21
remove some shims from the bottom = more droop
remove some shims from below spring = more droop & lower ride height
In general, more droop meaning more responsive with the trade off of less steering mid-corner and at corner exit.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)