RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 大家好！有野請教 [打印本頁]

作者: 醫九 時間: 2007-3-7 00:15
標題: 大家好！有野請教
我記得細過時見過人地玩油車，個哥哥仔係用一個好似磨機既電撻既，當佢撻著左架車之後，比油，架車係向後行！！

佢即刻熄車，再掉轉個電撻再撻過，嗯，比油又向反前行！

想問下 d 二沖程搖控車機器係咪可以兩邊都轉到架？

作者: pui 時間: 2007-3-7 00:36

登錄/註冊後可看大圖

作者: andrewlio 時間: 2007-3-7 00:43
邊會向後行ga?

作者: NOKIA 時間: 2007-3-7 00:44
是的!我就是你說的那個哥哥仔

作者: DieselEngine 時間: 2007-3-7 01:02

原帖由醫九於 7/3/2007 12:15 AM 發表
我記得細過時見過人地玩油車，個哥哥仔係用一個好似磨機既電撻既，當佢撻著左架車之後，比油，架車係向後行！！

佢即刻熄車，再掉轉個電撻再撻過，嗯，比油又向反前行！

想問下 d 二沖程搖控車機器係咪可 ...

想問下 d 二沖程搖控車機器係咪可以兩邊都轉到架？
係.

作者: 醫九 時間: 2007-3-7 01:14

原帖由 DieselEngine 於 2007-3-7 01:02 發表

想問下 d 二沖程搖控車機器係咪可以兩邊都轉到架？
係.

你認真答定係假答？我認真問的！

上面有人笑喎，唔知你地邊個真

作者: tungkee 時間: 2007-3-7 02:51
兩邊都著到 !!

作者: 醫九 時間: 2007-3-7 10:48

原帖由 tungkee 於 2007-3-7 02:51 發表
兩邊都著到 !!

唔該晒

作者: python 時間: 2007-3-7 11:10
inside the crank shaft chamber, the port of air intake and air exhaust were built for one rotate direction, although the engine might run at both direction, the process of air intake and exhaust must be worse than normal runing, it may cause the damage of the linkage of piston and crank shaft, correct me if anything wrong.

作者: cowcowlee 時間: 2007-3-7 12:09

原帖由 python 於 2007-3-7 11:10 發表
inside the crank shaft chamber, the port of air intake and air exhaust were built for one rotate direction, although the engine might run at both direction, the process of air intake and exhaust mu ...

not quite a damage will be made but the performance became worse since the incorrect air intake timing...

作者: justinwan 時間: 2007-3-7 22:31
撻到ga.....but 架車後吾識行, 因為有單向....

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)