RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 自作業~~ [打印本頁]

作者: miyavi69 時間: 2014-9-30 00:14
標題: 自作業~~
無意發現工具箱有個開關.....仲有LED~
[attach]836799[/attach][attach]836800[/attach][attach]836801[/attach]
完成~
[attach]836802[/attach][attach]836803[/attach][attach]836804[/attach]
仲有~1/16 SUMMIT~
[attach]836805[/attach][attach]836806[/attach][attach]836807[/attach]
原裝套燈幾光...不過....整到D線好亂...
[attach]836808[/attach][attach]836809[/attach]
同場加映!!買左油嘅E-REVO~~~
[attach]836810[/attach][attach]836811[/attach]
隻色好肉酸

作者: 965 時間: 2014-9-30 13:29
Nice body and tire wor ..

How do you like the Castle 1410 3800kv vs the Hpi version 4000kv? I did the same swap too, hardly notice any performance difference .. but seems temperature has dropped a bit .. but could be weather here .. (can go from +30 to -10 in a day ..

) so I would like to get some opinion ... I swap to 3800 mainly because I can use 5mm shaft ..

作者: Annie268 時間: 2014-9-30 16:06
very good.....

作者: Annie268 時間: 2014-9-30 16:07
very good

作者: george519 時間: 2014-9-30 16:31
落地玩未呀?

作者: miyavi69 時間: 2014-9-30 18:29

965 發表於 2014-9-30 13:29
Nice body and tire wor ..

How do you like the Castle 1410 3800kv vs the Hpi version 4000kv? I di ...

1410爆過hpi 嗰隻好多，而溫度都無咁高，不過電變最好用sc8嗰d;另外喺castle官網論壇爬過文，有人測過1410摩打3800Kv實際轉速係40xx,而hpi 嗰隻就37xx，有無負荷就唔知

作者: miyavi69 時間: 2014-9-30 18:30

george519 發表於 2014-9-30 16:31
落地玩未呀?

等你

作者: 965 時間: 2014-10-1 05:52

miyavi69 發表於 2014-9-30 18:29
1410爆過hpi 嗰隻好多，而溫度都無咁高，不過電變最好用sc8嗰d;另外喺castle官網論壇爬過文，有人測過141 ...

Interesting ... most I have seen, the HPI still a bit quicker (same gear) which make sense, it is 200kv higher ...

作者: miyavi69 時間: 2014-10-1 09:48

965 發表於 2014-10-1 05:52
Interesting ... most I have seen, the HPI still a bit quicker (same gear) which make sense, it is ...

i got this information from castle creation forum

castle 1410 using N38UH magnets and hpi use N35UH magnets,stator laminations .35mm on the HPI, .2mm on the Castle
amp drawing: 4000kv HPI ~151 amp ,Castle 3800~115 Amps,

作者: 965 時間: 2014-10-1 10:15
I think I saw that too .. but from one user .. If 115amp vs 151 .. that is HUGE diff .. and relief the Sidewinder lots ...

My Savage XS is sticked with the HPI 4000kv .. only run 2s ... (3s is out of control .. lol ) but for my WR8 .. the hip 4000kv is with 3mm shaft .. but most of my pinions are 5mm .. so I swapped to the Castle 3800 ..

作者: miyavi69 時間: 2014-10-1 10:19

965 發表於 2014-10-1 10:15
I think I saw that too .. but from one user .. If 115amp vs 151 .. that is HUGE diff .. and relie ...

5mm more durable~

作者: 965 時間: 2014-10-1 10:34

At least .. I can buy 5mm Mod 1 pinion ..

作者: miyavi69 時間: 2014-10-1 11:52

965 發表於 2014-10-1 10:34
At least .. I can buy 5mm Mod 1 pinion ..

something strange that mod 1 pinion is easy to get in kws..........................but 32p....many shop give me mod 1 when i ask for 32p....
32p close to 0.8 mod......

作者: 965 時間: 2014-10-1 12:24
Mod 1 always for 5mm shaft (1/8) wor... 32p.... Traxxas ma... More with 3mm....

作者: miyavi69 時間: 2014-10-1 13:11

965 發表於 2014-10-1 12:24
Mod 1 always for 5mm shaft (1/8) wor... 32p.... Traxxas ma... More with 3mm....

many sc truck using 32p and 5mm shaft,sc10 4x4, axial exo, mod 1 mainly for 1/8 scale ~
losi scte use mod 1 pinion

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)