標題: 3Racing 1:10 F113 F1 Racing Car w/ FREE Speed Passion Competition V3.0 Brushl... [打印本頁] 作者: Dinballian 時間: 2013-1-25 10:09 標題: 3Racing 1:10 F113 F1 Racing Car w/ FREE Speed Passion Competition V3.0 Brushl... 本帖最後由 Dinballian 於 2013-1-25 10:10 編輯
3Racing 1:10 F113 F1 Racing Car has been stocked!
There are 2 versions available in rcMart: 3Racing 1:10 RC Formula 1 Racing EP Car Kit #KIT-F113 & #KIT-F113SP
3Racing F113 is the first competitive F1 chassis race kit to bare the 3 Racing “Factory Racing Products” label, the introduction of this label was conceptualized with the idea of including the best materials in our high end race kits and to distinguish our line of successful Sakura car kits from the entry/mid-level to race level. All car kits to bare the “Factory Racing Products” label will feature the finest of materials namely imported high grade 7075 aircraft aluminum, imported woven carbon graphite, PTFE coated shock bodies and ball ends.
Front Suspension
The F113 was redesigned from scratch and shares very little parts with the successful F109, the F113 is the first to feature various innovative concepts previously unseen on mainstream F1 chassis currently available while maintaining the realistic looks of a real F1 car which in many cases is the fundamental success of the class. The F113 will feature a unique front suspension unlike anything available, dual Through Shaft Coil Spring Oil Filled Alum Dampers, Independent Double Wishbone Suspension and features adjustments such as Droop, Camber, Caster, Reactive Caster, Roll Center, Shock Angle, Ackermann with the entire infrastructure supported on 7075 Alum bulkheads.
Rear Suspension
The rear of the F113 employs a 1/12th pan car inspired design with the widely used single pivot ball, side springs and drag link rear suspension system with a longitudinal Symmetric Stroke Through Shaft Design rear Coil Spring Oil Filled Dampers to handle the front and rear weight transfers and another mounted transversely to handle the side to side damping.
Rear Drive Train (Picture shows early prototype motor
mount)
The F113 will come standard with a 1/12th scale type 1/4" rear axle and diff equipped with 1/8” stainless steel diff balls plus specially processed diff plates which gives it the extra hardness to handle any high powered brushless motor . Axle Height adjusters will allow adjustments in 0.5mm increments for precise ride height adjustments with any tire diameter.
The motor mount will be constructed from machined 7075 alum for the best rigidity and heat dissipation and will accommodate both Brushed and Brushless Motors.
Upper and Main Chassis
The 2.5mm main chassis and 2mm upper chassis are CNC machined from premier grade imported woven graphite. It will accommodate both standard and low profile servos with plenty of room for electronics. Chassis mounted battery pack stoppers will come standard to precisely position your Lipo battery packs on every installation whether you are using standard or shorty Lipo battery packs.
Steering
Steering on the F113 can be handled through Standard or Low Profile servos depending on the type of batteries and electronics you are using with a servo saver horn for most popular servos (23, 24, 25).
Aerodynamics
To maintain high speed stability and agility, the body, front and rear wings features a completely new design with the aim of providing the right amount of downforce while maintaining realistic looks, the body will as always be unpainted polycarbonate with a realistic hard plastic Driver Helmet and Ultra flexible impact resistant rear wing and front wing mount.
F113 and Speed Passion Power Combo
As part of our celebration in the launch of the F113, 3 Racing will feature a first time Cross Over Promotional Combo of a Standard F113 kit bundled with a Speed Passion 17.5R Power Plant and the Innovative Revention S engine management system.
The combo will be offered at a special price, your F113 will now have the power and control needed to race at the highest level.
