RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Genius CP負pitch時完全無力問題 [打印本頁]

作者: LamaV3 時間: 2012-4-13 21:20
標題: Genius CP負pitch時完全無力問題
本帖最後由 LamaV3 於 2012-4-13 21:21 編輯

話說我部新買的Genius CP去練Cup機, 一cup轉立即打負pitch,
好似唔係好夠力彈返上去, 只能係倒機下定住高度不能再升, 由於高度唔夠再Cup返正時就抄落地..............
我之前玩部MCPX RTF原裝seting, 一cup轉打負pitch好夠力彈返起部機令我有足夠時間再cup返正, 點解部Genius CP好似負pitch升力咁弱既??

我部Genius CP seting:
Idel油門: 100%  80%  65% 80%  100%
Idel Pitch: 20% 30%  50%  70%  80%

經師兄們提點後, 把Idel mode改為:

油門: 100%  85%  65%  85% 100%
pitch: 0%  25%  50%  75%  100%

再去試機, 點之一樣........一Cup轉, 油門拉到最低, 只能停止跌勢, 無力升返起undefined

再打Throhold觀察油門最底時負pitch夠唔夠, 點之真係唔夠負pitch,於是係TRVADJ到較PIT
到L150%(本來100%)

登錄/註冊後可看大圖

較完後負pitch最盡多左好多, 睇落似有足夠負pitch啦, 再試!!
點之都係唔得.....
於是單手捉實架機打idel試D力, 由油門中點開始試, 向上推轉速增加升力上升, 再把油門回中, 開始向下試, 竟然係油門越低, 轉速越慢....油門到底時轉速很慢, 向下力完全唔夠, 唔掛得cup轉後唔夠升力啦

拆左對槳試拍了段片呢, 今次試有點唔同, 油門中點至最底, 轉速好似完全唔變, 現在頭都大埋
http://www.youtube.com/watch?v=WSFKp5CHI48&feature=g-upl&context=G2453d02AUAAAAAAAAAA

作者: mrchow 時間: 2012-4-13 21:45
Set CP helicopter, 你要用pitch尺讀出角度.

經師兄們提點後, 把Idel mode改為:
油門: 100%  85%  65%  85% 100%
pitch: 0%  25%  50%  75%  100%
blade角度:  ??  ??  ??  ??  ??

作者: mrchow 時間: 2012-4-13 21:46
如何可以send 份資料給你?

作者: mrchow 時間: 2012-4-13 21:47
你可以參考Hirobo的CP機手冊. 他們如何SET Pitch.

作者: LamaV3 時間: 2012-4-13 23:10

mrchow 發表於 2012-4-13 21:45

登錄/註冊後可看大圖

Set CP helicopter, 你要用pitch尺讀出角度.

經師兄們提點後, 把Idel mode改為:

我淨係識用pitch尺度有flybar450機呢, 依部機仔槳咁細,而且又無flybar睇水平, 所以唔識度呢....

另外我以為Walkera出廠時乜唔係行程最高至最底點都有+/-10度嗎??

作者: mrchow 時間: 2012-4-14 01:05
I'm sorry, I havn't watch your attached film.
According to your attached film,
拆左對槳試拍了段片呢, 今次試有點唔同, 油門中點至最底, 轉速好似完全唔變, 現在頭都大埋
http://www.youtube.com/watch?v=W ... 2453d02AUAAAAAAAAAA

If the transmitter is OK, then your receiving part has somthing wrong. After switch to idel, u should get 100% THRD.

Since I havn't got Genius CP, I don't know its system.
May be you connect a server to THRD to check it.
Hope this can help you.

作者: chiu 時間: 2012-4-14 13:58
本帖最後由 chiu 於 2012-4-14 14:14 編輯

LamaV3 ching,

Are you sure your idle switch has been set up properly. Have you activate the idle ON/OFF switch.

作者: kamboy 時間: 2012-4-14 16:43
I think the setting of the transmitter got something wrong

作者: LamaV3 時間: 2012-4-14 21:10

chiu 發表於 2012-4-14 13:58

登錄/註冊後可看大圖

LamaV3 ching,

Are you sure your idle switch has been set up properly. Have you activate the idle ...

我的油門seting:
Normal: 0% 30% 50% 70% 100%
Idel 1 100% 80% 65% 80% 100%

油門最低時一拍idel1, 主槳即時由靜止加速度轉動, 咁樣唔係已經確定idel制生效嗎??

作者: LamaV3 時間: 2012-4-14 21:11

kamboy 發表於 2012-4-14 16:43

登錄/註冊後可看大圖

I think the setting of the transmitter got something wrong

我已經係跟Walkera的說明書set啦喎

作者: kamboy 時間: 2012-4-14 21:24
回復 LamaV3 的帖子

U have 2603 to test ?

作者: kamboy 時間: 2012-4-14 21:27
My frd use 2603 to fly cp, idle can normal operated

作者: LamaV3 時間: 2012-4-14 21:29

kamboy 發表於 2012-4-14 21:27

登錄/註冊後可看大圖

My frd use 2603 to fly cp, idle can normal operated

我是跟這裡下的說明書設定呢 http://www.rctw.net/thread-188352-1-1.html
2603很難設定, 不想用它呢

作者: kamboy 時間: 2012-4-14 21:31
回復 LamaV3 的帖子

Just fly to take some test

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)