RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 各位大大幫下手!! TEU-104BK 問題 [打印本頁]

作者: roy55699    時間: 2012-3-10 00:51
標題: 各位大大幫下手!! TEU-104BK 問題
我唔知點解個電變係咁閃燈但又唔動,唔知咩事?有大大幫到我嗎?

http://www.youtube.com/watch?v=s ... jByziE2AhsH1PvO4io=
作者: rcworldhk    時間: 2012-3-10 01:26
roy55699 發表於 2012-3-10 00:51
我唔知點解個電變係咁閃燈但又唔動,唔知咩事?有大大幫到我嗎?

http://www.youtube.com/watch?v=sy_Aj ...

幾T?motor
作者: roy55699    時間: 2012-3-10 07:59
好似係13T,但我之前試過用24T雙星金麼打都係唔得.....
作者: 榮~    時間: 2012-3-10 09:20
roy55699 發表於 2012-3-10 07:59
好似係13T,但我之前試過用24T雙星金麼打都係唔得.....

呢隻電變用唔到13T喎!
作者: 榮~    時間: 2012-3-10 09:29
roy55699 發表於 2012-3-10 00:51
我唔知點解個電變係咁閃燈但又唔動,唔知咩事?有大大幫到我嗎?

http://www.youtube.com/watch?v=sy_Aj ...

係咪未較中位?
作者: rcworldhk    時間: 2012-3-10 11:28
roy55699 發表於 2012-3-10 07:59
好似係13T,但我之前試過用24T雙星金麼打都係唔得.....

Do you have connect the red cable from ESC to receiver??  
作者: roy55699    時間: 2012-3-10 19:09
rcworldhk 發表於 2012-3-10 11:28
Do you have connect the red cable from ESC to receiver??

Yes! I had!! U can see the vedio
作者: rcworldhk    時間: 2012-3-10 19:17
roy55699 發表於 2012-3-10 19:09
Yes! I had!! U can see the vedio

TEU-104BK have not BCE system. Your receiver can support over 7.4V in-put??
作者: roy55699    時間: 2012-3-11 00:41
rcworldhk 發表於 2012-3-10 19:17
TEU-104BK have not BCE system. Your receiver can support over 7.4V in-put??

What can I do now?
作者: rcworldhk    時間: 2012-3-11 00:43
roy55699 發表於 2012-3-11 00:41
What can I do now?

good lucky
作者: roy55699    時間: 2012-3-11 00:47
rcworldhk 發表於 2012-3-11 00:43
good lucky

If I use NIMH, can I solve the problem?
作者: rcworldhk    時間: 2012-3-11 00:57
roy55699 發表於 2012-3-11 00:47
If I use NIMH, can I solve the problem?

Nimh or Nicd is 7.2V must okay.
作者: Allan007    時間: 2012-3-11 17:45
roy55699 發表於 2012-3-11 00:47
If I use NIMH, can I solve the problem?

師兄首先個紅色插仔係直接駁住你舊電,舊電幾多volt,隻接收、servo、同隻104BK內部控制線路就硬食緊幾多volt,但呢三樣野最高只可以行6V,所以你咁駁法唔燒都唔會長命。你要先買個BEC,條紅色線仔插去BEC既輸入,個BEC就會輸出6V,先插落隻接收Ch3。

言歸正傳,紅燈眨下眨下說明書話即係接收無比信號佢,試下先set中位,再唔係插隻104BK落Ch1,因為見你隻servo會郁,即係肯定有信號出。

重有就係要留意插落接收條線果三條芯既次序,不過臘過眼你應冇錯。有咩發現再大家研究。
作者: 榮~    時間: 2012-3-11 18:22
Allan007 發表於 2012-3-11 17:45
師兄首先個紅色插仔係直接駁住你舊電,舊電幾多volt,隻接收、servo、同隻104BK內部控制線路就硬食緊幾多 ...

唉!我都無用BEC架喎,但係我未有呢個問題!
作者: Allan007    時間: 2012-3-11 18:50
榮~ 發表於 2012-3-11 18:22
唉!我都無用BEC架喎,但係我未有呢個問題!

咁你有冇發覺隻servo"好好力"呢
作者: 榮~    時間: 2012-3-11 19:06
Allan007 發表於 2012-3-11 18:50
咁你有冇發覺隻servo"好好力"呢

我未試過裝左bec係點喎!
作者: spawn1126    時間: 2012-3-11 19:12
樓主個接收可以食7.4V電,用Ni-MH電無問題
作者: Allan007    時間: 2012-3-11 19:14
spawn1126 發表於 2012-3-11 19:12
樓主個接收可以食7.4V電,用Ni-MH電無問題

但係servo未必得麻
作者: spawn1126    時間: 2012-3-11 19:15
用li-po差滿電會係8.4V
作者: koyochan    時間: 2012-3-15 01:25
什麼是BEC....?
作者: Administrator    時間: 2012-3-15 02:15
2 things to check:
1: cable from the ESC to the receiver (if it connects or not)
2: use black pig motor,

if those 2 steps still fails, then your ESC is farked
作者: 558558    時間: 2012-5-16 15:30
Good Good Good




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/) Powered by Discuz! X3.2