RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 用開RI呔零既師兄門..... [打印本頁]

作者: 水都丸 時間: 2011-3-29 18:17
標題: 用開RI呔零既師兄門.....
條零真係好易爆.....
買左套新呔玩左三排電俾人一射就爆左.....
有冇方法可以加固？四十幾蚊一對零咁既質素......
d呔真係唔錯，零就弱不甘風.....
師兄們可否分享一下？

作者: sIUcHuN 時間: 2011-3-29 21:08
會否考慮改用F201wheel set?

作者: 水都丸 時間: 2011-3-29 21:57

會否考慮改用F201wheel set?
sIUcHuN 發表於 2011-3-29 21:08

登錄/註冊後可看大圖

有諗過呀，但唔確定Size裝唔裝到，同埋我係F104要改用咩先裝到201wheel呢？

作者: sIUcHuN 時間: 2011-3-29 22:36
回復 3# 水都丸
RIDE/TAMIYA wheel for F201耐用和平宜得多.
頭尾改103GT件便可以,.

PS:由於我不喜歡原裝103GT轉向杯OFFSET的設計,故此我改用頭416轉向杯.

作者: nel3838 時間: 2011-3-29 23:04

條零真係好易爆.....
買左套新呔玩左三排電俾人一射就爆左.....
有冇方法可以加固？四十幾蚊一對零咁既質 ...
水都丸發表於 2011-3-29 18:17

登錄/註冊後可看大圖

No Problem C-Hing, I have had the same experience to.

When the rubber and rim start to split, I used Lexan Car body Repair Glue (can buy in any RC car shop in KWS) to apply around the join between the rim and the rubber. It does not look nice but it works very well. I tested this technique on both Tamiya Rubber tyre and RIDE rubber tyres, as rims from both brands are brittle (easy to crack).

Once the glue dries, because it is slightly flexible, it stretchs a bit with tyres. So far all my repaired tyre/rims worked to the end of life the tyres (worn till hole comes thru).

Hope this helps all...

作者: 水都丸 時間: 2011-3-29 23:08

No Problem C-Hing, I have had the same experience to.

When the rubber and rim start to split, ...
nel3838 發表於 2011-3-29 23:04

登錄/註冊後可看大圖

上次同你響JV分享既方法同樣，但我現時情況係爆wheel.....

作者: 水都丸 時間: 2011-3-29 23:08

回復水都丸
RIDE/TAMIYA wheel for F201耐用和平宜得多.
頭尾改103GT件便可以,.

PS:由於我不喜歡原 ...
sIUcHuN 發表於 2011-3-29 22:36

登錄/註冊後可看大圖

謝謝師兄幫忙，等我又試下先

作者: nel3838 時間: 2011-3-29 23:15
本帖最後由 nel3838 於 2011-3-29 23:28 編輯

上次同你響JV分享既方法同樣，但我現時情況係爆wheel.....
水都丸發表於 2011-3-29 23:08

登錄/註冊後可看大圖

oh dear, that's too bad then, sorry. Although i wonder, if the glue was applied earlier, would it help to protect the rim from splitting??

作者: nel3838 時間: 2011-3-29 23:19

No Problem C-Hing, I have had the same experience to.

When the rubber and rim start to split, ...
nel3838 發表於 2011-3-29 23:04

登錄/註冊後可看大圖

Started a separate post with photos, here is the link.
http://bbs.rc-evo.com/viewthread.php?tid=211635&extra=

作者: 葉生 時間: 2011-3-30 10:39
之前我都有呢個問題.....有師兄介紹我用cross鈴代替 ri 既豆腐鈴.....

作者: 水都丸 時間: 2011-3-30 11:34

之前我都有呢個問題.....有師兄介紹我用cross鈴代替 ri 既豆腐鈴.....
葉生發表於 2011-3-30 10:39

登錄/註冊後可看大圖

用邊隻？邊度有得賣？

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)