RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 磨軑機一問 [打印本頁]

作者: evojacky 時間: 2010-10-19 18:28
標題: 磨軑機一問
係咪有分手動同自動磨軑機ka?仲有要幾錢一部ar?

作者: hardmankam 時間: 2010-10-20 14:53
回復 1# evojacky

係咪有分手動同自動磨軑機ka? --> 係
仲有要幾錢一部ar? --> 手動 <$1000, 自動 >$1500

作者: evojacky 時間: 2010-10-20 15:34
回復 2# hardmankam

唔該哂，手動會吾好嗎？

作者: hardmankam 時間: 2010-10-20 16:49
手動都 ok. 當然全自動會方便好多.
最重要是配把靚刀! (如 Hudy)

作者: move7648 時間: 2010-10-20 19:27
how does tires turner operate?

作者: hardmankam 時間: 2010-10-20 20:21
you stick the foam tire in an adaptor. it will rotate and there is a knife to cut the tire to a pre-set diameter.

作者: hardmankam 時間: 2010-10-20 20:22
example here:
http://www.youtube.com/watch?v=ar4sZySYJd8

作者: move7648 時間: 2010-10-20 22:10
明晒!

跑JV個場, 一套呔有幾長壽命?

作者: hardmankam 時間: 2010-10-20 22:20
1 day (or 6 packs of battery) uses about 3mm.

BUT the left and right tires will NOT wear at the same rate. So its best to switch your L & R tires after 2 to 3 runs.

作者: move7648 時間: 2010-10-20 22:23
so 1 set tires can least for around 2 days

作者: hardmankam 時間: 2010-10-21 00:42
Speedmind tires are very thick... about 55mm to begin. so it will last you ~ 4 days
Jaco, excced, and ATS are much thinner, about 50mm to begin, so ~ 2 days

at JV, front tires wear much faster than rear tires.

作者: Buzzcow 時間: 2010-10-21 01:27

Speedmind tires are very thick... about 55mm to begin. so it will last you ~ 4 days
Jaco, excced, ...
hardmankam 發表於 2010-10-21 00:42

登錄/註冊後可看大圖

at JV, front tires wear much faster than rear tires.

totally agree!

作者: hardmankam 時間: 2010-10-21 12:21
回復 10# move7648

While thick tires give you more runs, it is easier to chunk (爆/裂) making the tire very unstable or unusable. You will have to repair (補軑) and will need a 磨軑機.

Of course professionals use 磨軑機 because of performance and setting purposes. They usually use rear tires of 44-46mm and front tires of 42-44mm. 3 to 4 runs on later, they will throw them away.

作者: evojacky 時間: 2010-10-21 17:30

回復 move7648

While thick tires give you more runs, it is easier to chunk (爆/裂) making the ti ...
hardmankam 發表於 2010-10-21 12:21

登錄/註冊後可看大圖

如果一買返離得48mm尾軑其實都算薄la
可以唔用磨軑機都可以wo?

作者: hardmankam 時間: 2010-10-21 18:22
本帖最後由 hardmankam 於 2010-10-21 18:27 編輯

yes, these are called 'pro cut' tires! (or race ready)
But pro drivers still think 48mm is too thick. They need to trim 2mm to '開軑'.

作者: evojacky 時間: 2010-10-21 19:30
本帖最後由 evojacky 於 2010-10-21 19:33 編輯

回復 15# hardmankam

跑一排電都無左2mm la
其實有無咩脾子係好用d呢食地d

作者: hardmankam 時間: 2010-10-21 22:12

回復 hardmankam

跑一排電都無左2mm la
其實有無咩脾子係好用d呢食地d
evojacky 發表於 2010-10-21 19:30

登錄/註冊後可看大圖

Jaco is good.

作者: evojacky 時間: 2010-10-21 23:05
回復 17# hardmankam

tomorrow try sin i have buy it ar!!!

作者: Buzzcow 時間: 2010-10-21 23:16

回復 hardmankam

tomorrow try sin i have buy it ar!!!
evojacky 發表於 2010-10-21 23:05

登錄/註冊後可看大圖

You can found jaco? seems no stock wor...

作者: evojacky 時間: 2010-10-22 00:28
本帖最後由 evojacky 於 2010-10-22 00:29 編輯

回復 19# Buzzcow

u can use ATS for front....Jaco for rear
i buy it in [紅星]...ar

作者: hardmankam 時間: 2010-10-22 00:40
ATS is also pretty good.

作者: billlkyy 時間: 2010-10-22 01:04
yokomo tire medium 同 farm 邊隻軟D?

作者: hardmankam 時間: 2010-10-22 01:15
Medium 軟D

Soft = 軟軑
Medium = 中硬度軑
Firm/Hard = 硬軑

作者: billlkyy 時間: 2010-10-22 01:30
本帖最後由 billlkyy 於 2010-10-22 01:52 編輯

買套yokomo medium 頭+32尾try try先,在jv玩5排電已ko左對35頭呔,去呔超快,medium同farm邊隻接近35多D呢?

作者: Buzzcow 時間: 2010-10-22 01:31
回復 20# evojacky

Many Thanks!

作者: xrayonly 時間: 2010-10-22 11:02
GQ 部磨呔機(紅X)見有得賣,而我見價錢比Hudy果隻
平1K到,請問大家點睇哩?

作者: hardmankam 時間: 2010-10-22 11:19
本帖最後由 hardmankam 於 2010-10-22 11:28 編輯

GQ 把刀幾好 gar. (Tungsten Carbide cutter = 超硬)
機身好唔好就不知道.

作者: jf813 時間: 2010-10-22 13:52
GQ ok ar. As it use large motor so very powerful. Same as q-world. Not sure about other brand la. For the cutter I am not sure as I am using the Hudy one now. Very good and stay sharp for very long time.

作者: xrayonly 時間: 2010-10-22 18:12

GQ ok ar. As it use large motor so very powerful. Same as q-world. Not sure about other brand la. ...
jf813 發表於 2010-10-22 13:52

登錄/註冊後可看大圖

Thx ching 現在Hudy咩價，請問？

作者: hardmankam 時間: 2010-10-22 18:13
Yeah, I am using Q-world + Hudy cutter... very good combination @ a decent price.

作者: hardmankam 時間: 2010-10-22 18:14
回復 29# xrayonly

Hudy > $3xxx
GQ ~ $23xx

作者: xrayonly 時間: 2010-10-22 18:58

回復 xrayonly

Hudy > $3xxx
GQ ~ $23xx
hardmankam 發表於 2010-10-22 18:14

登錄/註冊後可看大圖

Ching Hudy 35xx 得唔得？

作者: hardmankam 時間: 2010-10-22 19:14
本帖最後由 hardmankam 於 2010-10-22 19:15 編輯

回復 32# xrayonly

RCMxrket (1/F) website listed
Hudy @ US479 ~ HK3700
'Three' Racing @ US200 ~ HK1500

作者: xrayonly 時間: 2010-10-22 20:19
Thx ching !

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)