RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 那裡有 2 mm 鋼枝賣? [打印本頁]

作者: Very_Newbie    時間: 2009-6-9 18:14
標題: 那裡有 2 mm 鋼枝賣?
想用泥自製船軸。
作者: truckman    時間: 2009-6-9 18:55
想用泥自製船軸。
Very_Newbie 發表於 2009-6-9 18:14

go to旺角新填地街揾
作者: 567    時間: 2009-6-9 20:48
對新填地街
作者: tekin708    時間: 2009-6-9 21:17
新填地街 but it cut by yourself
作者: audioyiu    時間: 2009-6-9 21:30
新填地街一定有,仲會幫你cut tim
作者: Andrew168    時間: 2009-6-10 12:10
自製船軸其實唔難, 但要有設備先做得到先難, 如有細車床就得
作者: Very_Newbie    時間: 2009-6-10 15:03
自製船軸其實唔難, 但要有設備先做得到先難, 如有細車床就得
Andrew168 發表於 2009-6-10 12:10




車床我就冇啦,不過有一個虎拑加一個 2 mm 攪牙 Die (前日係 善X 買,要成 $75)。
今日去過新填地街見到間好大間買鋼材既舖,話最幼得 3 mm
作者: Andrew168    時間: 2009-6-10 15:08
車床我就冇啦,不過有一個虎拑加一個 2 mm 攪牙 Die (前日係 善X 買,要成 $75)。
今日去過新填地街見到間好大間買鋼材既舖,話最幼得 3 mm
Very_Newbie 發表於 2009-6-10 15:03



買軸套大約都係 70 ~ 90 左右, 何必自己整呢
作者: Andrew168    時間: 2009-6-10 15:14
本帖最後由 Andrew168 於 2009-6-10 15:16 編輯

去 "得搶" 問吓有冇2mm軸套好
作者: Very_Newbie    時間: 2009-6-10 15:41
去 "得搶" 問吓有冇2mm軸套好
Andrew168 發表於 2009-6-10 15:14



己經係 "得搶" 買左三套軸( $48 一套)用泥改隻 Hermann Marwede (三軸船),
中軸冇問題,但左右軸吾夠長,因有 10 cm 伸出隻船外。

作者: batmanhu    時間: 2009-6-10 16:05
己經係 "得搶" 買左三套軸( $48 一套)用泥改隻 Hermann Marwede (三軸船),
中軸冇問題,但左右軸吾夠長,因有 10 cm 伸出隻船外。
Very_Newbie 發表於 2009-6-10 15:41

一定要鋼支??? 點解唔試下銅支。 2mm銅支再加銅管
作者: Very_Newbie    時間: 2009-6-10 18:06
一定要鋼支??? 點解唔試下銅支。 2mm銅支再加銅管
batmanhu 發表於 2009-6-10 16:05



銅管可以用番果套裡面枝 stern tube (銅造的),但是要整過枝長 d 鋼軸。
d 鬼佬網話同類金屬磨擦吾係敢好,所以出面 d 套裝船軸多數都係銅管鋼軸。
作者: joeleung    時間: 2009-6-10 18:45
銅管可以用番果套裡面枝 stern tube (銅造的),但是要整過枝長 d 鋼軸。
d 鬼佬網話同類金屬磨擦吾係敢好,所以出面 d 套裝船軸多數都係銅管鋼軸。
Very_Newbie 發表於 2009-6-10 18:06


so do you know why avoiding friction contact for the same material?
better think before believing. Yes, I agreed the forum said is right,
but i can tell you that it is meaningless unless your model boat runs 24hrs non-stop for many years.
besides, there are two bushes at the both ends of the stern tube, so no contacts in actual for the shaft and shaft tube.
And also lubricant was needed to fill inside the stern tube, so there are a thin lubricant layer formed at the middle of the contact surface to protect both sides of material.
作者: Very_Newbie    時間: 2009-6-10 19:11
so do you know why avoiding friction contact for the same material?
better think before believing. Yes, I agreed the forum said is right,
but i can tell you that it is meaningless unless your m ...
joeleung 發表於 2009-6-10 18:45



In fact, I did not read the forum messages in detail .
I went to 新填地街 this morning to try my luck.  I think I can settle for a brass propeller shaft if the steel counterpart is so difficult to get.
(Might go to "Sunny" on Friday)
作者: 新兩兄弟    時間: 2009-6-10 20:53
你可以用14號不透鋼電焊枝有2mm,在新填地街有




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/) Powered by Discuz! X3.2