求救，引擎吾著，點解？

剛剛裝好部3R，用OS 12TZ3port 引擎，但系著吾到，吾知點解。
油可以進到引擎到，但是不能燃燒，我用的系放電芯的火嘴電，系吾系尼個問題。

另外想問問灣仔橋底點去？我想直接去找人幫忙得吾得啊？

[ 本帖最後由 太古少 於 2007-1-23 00:33 編輯 ]

你缸油方了好久咩= =

那麼啡的???

橋低便是銅鑼灣灣消防局向海隊方向行出去便找到

係啊，放佐好久咯

係咪有影響啊

原帖由 太古少 於 2007-1-23 00:28 發表
剛剛裝好部3R，用OS 12TZ3port 引擎，但系著吾到，吾知點解。
油可以進到引擎到，但是不能燃燒，我用的系放電芯的火嘴電，系吾系尼個問題。

另外想問問灣仔橋底點去？我想直接去找人幫忙得吾得啊？

你去問一個中年老人,揸10仔720車個人la

原帖由 毒魚 於 2007-1-23 00:41 發表
你缸油方了好久咩= =

那麼啡的???

橋低便是銅鑼灣灣消防局向海隊方向行出去便找到

坐地鐵到得到不了啊？

I got an OS 12TZ 5 ports. Yes.
It is an enginee very hard to start when it was new.
Try harder, and try more....that was my suggestion.

原帖由 VoneRRR 於 2007-1-23 03:58 發表
I got an OS 12TZ 5 ports. Yes.
It is an enginee very hard to start when it was new.
Try harder, and try more....that was my suggestion.

每部機都要break in la,無分3,5,7, port

原帖由 VoneRRR 於 2007-1-23 03:58 發表
I got an OS 12TZ 5 ports. Yes.
It is an enginee very hard to start when it was new.
Try harder, and try more....that was my suggestion.

Thanks for your suggestion!!! I will try.

甘你用佐多久先run 到啊？

[ 本帖最後由 太古少 於 2007-1-23 19:39 編輯 ]

原帖由 太古少 於 2007-1-23 13:04 發表


Thanks for your suggestion!!! I will try.

甘你用佐多久先run 到啊？

Hard to say how long....since i seperated for few days to do it. (being tired and having rest)
But i remember the first time i started enginee, i spent for at least 15mins.

Yeah. I know no matter how many ports also need time to break in.
But,there are not just only one person told me that OS enginee is not that easy to start comparing with the other brands.

原帖由 lokaman 於 2007-1-23 04:00 發表

每部機都要break in la,無分3,5,7, port

Yes a

[ 本帖最後由 VoneRRR 於 2007-1-24 15:12 編輯 ]

用工業用既 heat gun 吹熱 heatsink...

無既風筒都可以,不過要吹耐d...吹到盪手再試下...

富機會易著好多....

原帖由 太古少 於 2007-1-23 01:09 發表
係啊，放佐好久咯

係咪有影響啊

新機最好用返新鮮油...

好熱氣呀!

[ 本帖最後由 devilstar 於 2007-1-25 00:22 編輯 ]

原帖由 devilstar 於 2007-1-25 00:05 發表
好熱氣呀!

咩也意思啊？？

原帖由 devilstar 於 2007-1-25 00:05 發表
好熱氣呀!

好黃...要食多 d 生果...!

Could u rotate the flywheel in starter easily now?  If yes, then no need to use heat gun.  U must check if there is other problem.  Maybe, the plug is mal-functioning.   

If the engine is very tight(your starter cannot rotate it),  u must use heat gun or other means to burn the heat sink.  After heating up, immediately start your engine.  Upon starting up your engine, dont stop it and add oil to continue running.  Dont pull full throttle and try keep the temp around 80 degree.  Having run around 5-6 tanks, the engine will be very easy to start ga na. (If u stop the engine, then u need to use heat gun to burn the engine again)  No harm to continue running if the temp is acceptable.

I had TZ in the past.  It was difficult to start the engine in the beginning.  But once u complete the run-in, u will enjoy it.  TZ is very good engine in that range of price.

Thanks you, my engine is a little bit tight , maybe that is the problem.