RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
樓主: tkwcrash
打印 上一主題 下一主題
收起左側

1:8 GT & 電平8 玩家專區

  [複製鏈接]
161#
benz1850 發表於 2013-5-19 16:00:19 | 只看該作者

Hi,

A picture more than thousand word.  

I apply the setting from Viper's web site which indicate the setting for GT.   It just run for one lap and stop in the middel of the TRC.  And then smoking comming out.  Lots of Ching saw that, what a suck ESC.

May be Viper or the shop will challenge my car's setting is making that.  The fact is, I change to HobbyWing's ESC, after the burning of Viper.  Exactly the same setting on the GT8, no a single screw change.  I can run very comfort and FAST.  What a shame for Viper.  May be Chinese is the king

My car normally run with Tekin RX8 for more than 1/2 year with more extreme setting like 41/22 and NO any issue.  Just may be it getting old and soem jittering during run that making me consider to change.

If Viper say it is so powerful, why don't load some more friendly setting by default?  Or just put some immature product to the market and ask player to pray?

I tried RX8, HW, Crowcrow and Viper.  The previous third is good to run, easy to setup.  The most powerful is Viper ON BURNING!!!!!!!

GOOD LUCY and try to avoid from it!!!!


162#
DLLL 發表於 2013-5-19 19:01:56 | 只看該作者
有冇Ching試過換快齒後應該用什麼齒比?我未換之前用42/18,150A及2750KV都冇事。
163#
benz1850 發表於 2013-5-19 19:13:52 | 只看該作者
DLLL 發表於 2013-5-19 19:01
有冇Ching試過換快齒後應該用什麼齒比?我未換之前用42/18,150A及2750KV都冇事。 ...

師兄, 我尋日用同你一樣, 快呀。42/17。 HW 同812。17呀沒問題。18呀好快。 同一setting, 17呀, Viper 燒左。相可看上面個post.
164#
DLLL 發表於 2013-5-19 19:26:33 | 只看該作者
benz1850 發表於 2013-5-19 19:13
師兄, 我尋日用同你一樣, 快呀。42/17。 HW 同812。17呀沒問題。18呀好快。 同一setting, 17呀, Vipe ...

我而家未試好,昨日在JV行45/16,覺得好似未換快齒前行42/18還快d
165#
tungming508 發表於 2013-5-19 20:32:26 | 只看該作者
DLLL 發表於 2013-5-19 19:26
我而家未試好,昨日在JV行45/16,覺得好似未換快齒前行42/18還快d

JV行45/16
有冇check 溫度係咪低左?
166#
DLLL 發表於 2013-5-19 20:41:49 | 只看該作者
可能我之前用2把風扇40mm&50mm外置11V吹摩打,但而家只用40mm吹摩打50mm吹電變,所以摩打兩個做法都係約70度
167#
0433433 發表於 2013-5-19 20:50:10 | 只看該作者
好似45/16穩陣d 冇咁易過熱
168#
DLLL 發表於 2013-5-19 22:49:52 | 只看該作者
0433433 發表於 2013-5-19 20:50
好似45/16穩陣d 冇咁易過熱

係呀!不過會慢d啦
169#
tungming508 發表於 2013-5-23 20:28:16 | 只看該作者
試下18同45,反正你有
170#
DLLL 發表於 2013-5-26 09:25:04 | 只看該作者
tungming508 發表於 2013-5-23 20:28
試下18同45,反正你有

其實45/16都好熱
171#
tungming508 發表於 2013-5-28 03:18:31 | 只看該作者
咁唯有等下Tekin RX8第二代啦
172#
ed003 發表於 2013-5-28 15:09:29 | 只看該作者
本帖最後由 ed003 於 2013-5-28 15:11 編輯

Just bought Viper and SP 2750KV motor
173#
kennethcheng 發表於 2013-5-28 20:23:28 | 只看該作者
good luck, me and my friend burn 3 of them already.....
174#
tungming508 發表於 2013-5-28 21:33:43 | 只看該作者
祝君好運了
175#
ed003 發表於 2013-5-28 22:08:13 | 只看該作者
不用了,可能firmware 出問題,對不到控,廠跟進中,不过要讚吓林sir佢已盡咗力幫手
176#
benz1850 發表於 2013-5-28 23:43:38 | 只看該作者
ed003 發表於 2013-5-28 15:09
Just bought Viper and SP 2750KV motor

等你好燒息。。。。。。
177#
benz1850 發表於 2013-5-28 23:46:07 | 只看該作者
ed003 發表於 2013-5-28 22:08
不用了,可能firmware 出問題,對不到控,廠跟進中,不过要讚吓林sir佢已盡咗力幫手 ...

嘩,獲獲新奇獲獲金。Viper 真好野。
178#
ed003 發表於 2013-5-29 16:14:50 | 只看該作者
原来係條sensor cable 唔work 仲搞咗咁耐
179#
auaxq 發表於 2013-5-30 12:02:14 | 只看該作者
咁多位師兄,各位好!想問下摩打坐個位個中齒用限滑叉速同原裝個叉速有咩分別?平地?沙地?邊種合適D?多謝指教
180#
whatafather 發表於 2013-5-31 23:56:08 | 只看該作者
原裝中間個大餅算有差速咩?好似direct drive 嚟喎...............
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2024-4-29 03:59 , Processed in 0.172885 second(s), 16 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表