RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

 找回密碼
 新玩家註冊
搜索
查看: 2279|回復: 9
收起左側

RX8 Clutch Shoe Break In Procedure

[複製鏈接]
beebone 發表於 2011-5-7 00:15:22 | 顯示全部樓層 |閱讀模式

遊客登錄

您需要 登錄 才可以下載或查看,沒有帳號?新玩家註冊

x
本帖最後由 beebone 於 2011-5-7 00:18 編輯


                               
登錄/註冊後可看大圖

                               
登錄/註冊後可看大圖





To ensure that the RX8 clutch shoe works properly and for a long time, it is very important to run in the clutch shoe.
Please follow these run-in steps to help ensure proper clutch operation:


                               
登錄/註冊後可看大圖
1. Install clutch according to manual.

2. Check that the spring preload is not too much; for run-in process use less preload.

3. When you start the engine, the clutch should start engage under low RPM.
If the clutch engages only under high RPM, stop the engine and loosen the spring preload collar. Repeat until the clutch engages under low RPM.

4. Run in the clutch shoe on the track, or on the starter box if you have only limited time.
(We recommend running it in on the track.)

5. Run in the clutch shoe for 1 tank of fuel using a soft preload setting, and then after that slightly tighten the spring preload. DO NOT run in the clutch shoe under high RPM.

6. Continue this process until the clutch shoe is properly run in; this will be indicated by a dark and glossy surface colour on the top of the clutch shoe.




chungtsai 發表於 2011-5-11 18:28:22 | 顯示全部樓層
thx C-hing!

不過我都唔會轉玩懷舊伯。
 樓主| beebone 發表於 2011-5-11 19:56:41 | 顯示全部樓層
chungtsai 發表於 2011-5-11 18:28
thx C-hing!

不過我都唔會轉玩懷舊伯。

遲d會ga la
xitrd 發表於 2011-5-19 23:32:18 | 顯示全部樓層
Not sure if this is related to some bros radio jam issue
 樓主| beebone 發表於 2011-5-20 09:46:55 | 顯示全部樓層
xitrd 發表於 2011-5-19 23:32
Not sure if this is related to some bros radio jam issue

Radio jam is not related to clutch shoe breakin in, I have no jamming issue at all.
The Rx is located inside the box, same as NT-1. How come NT-1 doesnt have this issue but RX8 does? Not possible

Some said the glinding frequency influent the RX. Not possible as well, not sure the racers using AM / FM bands or not, for sure 2.4GHz has descrembled signal and frequency wave length must be much shorter then glinding noise from the clutch. How much rpm can the engine reach??!? 40k something rpm max.

But I've found something interesting yesterday, this is the issue from NT1 already. The front lower shock ball head, the 3x8mm hex screw came lose with the ball head. So the car can't turn. the hex screw is too short, the lower arm can't hold the hex screw tight enoguh and vibration made the screw losing.
xitrd 發表於 2011-5-24 14:42:24 | 顯示全部樓層
Ic…. Thanks for the opinion beebone.  Personally I don’t experience any jam to my RX8. Just trying to see if this is related to some other bro’s radio issue with their maiden run of their cars.
 樓主| beebone 發表於 2011-5-24 14:49:22 | 顯示全部樓層
xitrd 發表於 2011-5-24 14:42
Ic…. Thanks for the opinion beebone.  Personally I don’t experience any jam to my RX8. Just trying ...

I can say KO RX will have cut off on any car, this is well known issue.
And some found that Sanwa in HRS mode will used up the battery very soon. I set it back to Normal mode.
xitrd 發表於 2011-5-24 14:50:08 | 顯示全部樓層
They were using 4pk....
 樓主| beebone 發表於 2011-5-24 14:57:52 | 顯示全部樓層
xitrd 發表於 2011-5-24 14:50
They were using 4pk....

Normally on Ko and Sanwa, dont know about Futaba. Anyway, check the top deck, esp the flex screw, just bolt on firm but not hard, no vibration or lose, and do some insulation on the RX box, it will be fine.
altezza 發表於 2011-5-25 01:14:40 | 顯示全部樓層
chungtsai 發表於 2011-5-11 18:28
thx C-hing!

不過我都唔會轉玩懷舊伯。

玩藍色的士
您需要登錄後才可以回帖 登錄 | 新玩家註冊

本版積分規則

手機版|小黑屋|RC EVOLUTION - 遙控工房

GMT+8, 2024-3-29 19:55 , Processed in 0.049445 second(s), 16 queries , Gzip On.

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回復 返回頂部 返回列表