RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: About F103rm 調教 [打印本頁]

作者: casyyeung 時間: 2011-5-28 14:38
標題: About F103rm 調教
Ching 們，本人是 F1 新手， I want to ask how to adjust the rear height of the car and the 珠差應該 how to adjust. If I play in Jv, should use 海綿呔 or 膠呔？楂 F1 同 touring 有什麼分別？請 Ching 多多指教，thx!

作者: DicksonGlacier 時間: 2011-5-28 16:11
有同一樣的問題，請高人門指點一下。

作者: cyberkohk 時間: 2011-5-28 16:46
用標準設定加海綿呔比較容易控制 , 玩上手至更改設定 , 控制有一定難度因反應及加速比touring快另類快感

作者: nel3838 時間: 2011-5-28 20:30
本帖最後由 nel3838 於 2011-5-28 20:31 編輯

for new F1 drivers, must make sure the rear wheel dont go loose. Go for understeer than oversteer. Like Cyberkohk Ching said, use Tamiya original foam tyres are good as a start.

And use Tyre "Water" for the rear only in the beginning.

The centre disc damper, keep very loose (with light oil only), and keep rear diff very loose also.

One personal advice, at JV, many have had bad accident on fast straight (due to the brick blocks). Not only loose money to buy parts, but keeps cutting play time short for new drivers. So best advice at JV is NOT to drive on the big straight, but on the little big straight. You can have longer play time.

Hope this helps.

作者: casyyeung 時間: 2011-5-28 20:34
Thx, all Chings.

作者: kevin-ysl 時間: 2011-5-28 22:21
本帖最後由 kevin-ysl 於 2011-5-28 22:23 編輯

先用原裝動力...
唔好set乜野外八字內八字~~
用原裝果套呔~~
珠差收到有幾緊得咁緊~~
落場跑幾排電...
禮讓吓d超快師兄~~
F103好耐炒嘅~~~
個幾月後你已經會再問有乜要求架啦~~
千萬唔好而家問落乜野摩打快...邊隻呔咬...邊隻升級件正..
因為係冇需要~~~原裝快到你唔信~~
又萬一你已經上左D強勁無刷等大量升級件....恭喜你...
你會好快放棄~~

玩F1有個特色...就係要忍!!

作者: photocatcher 時間: 2011-5-29 00:18

kevin-ysl 發表於 2011-5-28 22:21

登錄/註冊後可看大圖

先用原裝動力...
唔好set乜野外八字內八字~~
用原裝果套呔~~

非常同意
"又萬一你已經上左D強勁無刷等大量升級件....恭喜你...
你會好快放棄~~

玩F1有個特色...就係要忍!!"

作者: nel3838 時間: 2011-5-29 06:42

photocatcher 發表於 2011-5-29 00:18

登錄/註冊後可看大圖

非常同意
"又萬一你已經上左D強勁無刷等大量升級件....恭喜你...
你會好快放棄~~

X 2 ... Haha

作者: lf2c 時間: 2011-6-7 19:02
本帖最後由 lf2c 於 2011-6-7 19:03 編輯

乜用原裝配套真係好快架???

因為未玩過所以好想知道下..........

作者: casyyeung 時間: 2011-6-7 20:06
另外 Ching, 用有感 ESC 會否 better than 無感呢？

作者: nel3838 時間: 2011-6-8 13:39
有感 ESC with Turbo option is great fun for F1 cars. And also better proportion throttle control which is important for good 2WD controls.

作者: avenger 時間: 2011-6-8 23:19

nel3838 發表於 2011-6-8 13:39

登錄/註冊後可看大圖

有感 ESC with Turbo option is great fun for F1 cars. And also better proportion throttle control wh ...

Apart from Hobbywing, which brand have turbo ESC good for F1?

作者: nel3838 時間: 2011-6-8 23:22

avenger 發表於 2011-6-8 23:19

登錄/註冊後可看大圖

Apart from Hobbywing, which brand have turbo ESC good for F1?

I like HW already (and very good repair service)

. Perhaps the sister company Speedpassion.

作者: avenger 時間: 2011-6-8 23:28

nel3838 發表於 2011-6-8 23:22

登錄/註冊後可看大圖

I like HW already (and very good repair service). Perhaps the sister company Speedpassion.

Thanks C Hing!!

作者: avenger 時間: 2011-6-8 23:28

nel3838 發表於 2011-6-8 23:22

登錄/註冊後可看大圖

I like HW already (and very good repair service). Perhaps the sister company Speedpassion.

Thanks C Hing!!

作者: corkscrew 時間: 2011-6-13 17:07
小弟而家都玩緊F104 PRO
原裝SETTING搭雙星23T + 4200 LIPO電都已經好快....

作者: casyyeung 時間: 2011-6-13 18:20
I now using hobbywing 8.5T brushless and 4200 LIPO , but the speed is not so fast why?

作者: kevin-ysl 時間: 2011-6-14 00:33
用幾大摩打齒??

作者: casyyeung 時間: 2011-6-14 08:14
本帖最後由 casyyeung 於 2011-6-14 09:57 編輯

64 搭 17

作者: casyyeung 時間: 2011-6-14 10:00
And I also want to ask how to change the camber in the front of 103rm?

作者: kevin-ysl 時間: 2011-6-14 10:04
試下20齒~~
我試過用17.5t配21齒幾啱走!
照計你用20齒會over 小小…

作者: strike 時間: 2011-6-14 10:35
you need to but another parts

作者: casyyeung 時間: 2011-6-14 14:07
What parts Ching, can you show me some photo, thx?

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)