Xray Composite Dual Servo Saver Arm for T3 T4 #XR-302526
Set of 2 molded arms for dual servo saver, made form tough composite material. Set of left and right arms.
Xray Composite C-Hub Right 2 degree – Medium – Rubber Spec for T2 T3 T4 #XR-302361
This is a optional XRAY Molded Composite Medium Rubber-Spec 2° Right Side C-Hub, and is intended for use with the XRAY T2 family of vehicles. This Molded composite C-hub for the right side steering block has a pre-set caster angel of 2°. Medium rigidity for rubber-tire racing. Use with matching left-side C-hub #XR-302362.
This C-hub has large openings for quicker & easier assembly/disassembly of CVDs. The entire CVD assembly can be easily inserted/removed through the C-hub without the need for disassembly, and the large openings prevent binding of the CVD in serious crashes.
The C-hubs are available in all standard caster angles and are also available in two different rigidities that are optimized for
particular racing conditions. The EU Edition includes medium rigidity (M) C-hubs
specially optimized for rubber-tire racing, while the US Edition includes hard
rigidity (H) C-hubs specially optimized for foam-tire racing.
Xray Composite C-Hub Left 2 degree – Medium – Rubber Spec for T2 T3 T4 #XR-302362
This is a optional XRAY Molded Composite Medium Rubber-Spec 2° Left Side C-Hub, and is intended for use with the XRAY T2 family of vehicles. This Molded composite C-hub for the right side steering block has a pre-set caster angel of 2°. Medium rigidity for rubber-tire racing. Use with matching right-side C-hub #XR-302361. This C-hub has large openings for quicker & easier assembly/disassembly of CVDs. The entire CVD assembly can be easily inserted/removed through the C-hub without the need for disassembly, and the large openings prevent binding of the CVD in serious crashes.
The C-hubs are available in all standard caster angles and are also available in two different rigidities that are optimized for particular racing conditions. The EU Edition includes medium rigidity (M) C-hubs specially optimized for rubber-tire racing, while the US Edition includes hard rigidity (H) C-hubs specially optimized for foam-tire racing.
Xray Ball End 4.9mm w/ Thread 6mm for T2 T3 T4 #XR-302653
Threaded 4.9mm ball end with 6mm thread for rear suspension on T2 family of cars to replace the ball + screw assembly. These balls are great for use with Xray closed composite ball joints #XR-302661 but also work with standard open ball joints.
Xray Anti-Roll Bar Front 1.3mm for T4 #XR-302493
This is a replacement XRAY 1.3mm Front Anti-Roll Bar, and is intended for use with the XRAY T4 1/10 scale electric touring car. This is the stock front anti-roll bar.
Xray Composite Spur Gear 106T / 64P for T1 T2 T3 T4 #XR-305876
XRAY precision molded offset spur gear 106 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass.
Xray 4S Spring – Set C = 2.9 for T4 #XR-308277
The all-new linear 4S springs marked 2.9. 4S springs have been specifically designed to complement the SLP shocks and are 20mm long. Set of 2.
The 4S springs, like all the other XRAY springs, are manually measured, selected and matched into pairs to guarantee precisely equal length and damping characteristics.
Xray Aluminum Lower Suspension Block – Orange for T3 T4 #XR-302045-O
CNC-machined aluminum lower suspension block which is part of all-new suspension holder system allows suspension arms to be mounted independently from the diff bulkheads.
Xray Aluminum Lower Front Suspension 1-Piece Holder – Orange v2 for T3 T4 #XR-302047-O
The optional 1-piece aluminum suspension holder is a direct replacement for the standard rearward holders of the FRONT suspension. The aluminum suspension holder reinforces the chassis and will help to prevent chassis damage in hard crashes. The aluminum holder will also make the front suspension a bit stiffer and give the car slightly less steering response.
Item no.: XR-302047-O
Xray Aluminum Lower Rear Suspension holder – Orange for T4 #XR-302050-O
Optional 1-piece aluminum rear suspension holder is a direct replacement for the standard forward holders of the REAR suspension. This holder is recommended to use for more steering in high grip conditions only, as it increases stability. CNC-machined alu lower rear suspension holder which is part of suspension holder system allows suspension arms to be mounted independently from the diff bulkheads.
Xray 50mm Drive Shaft – Hudy Spring Steel for T2 T3 T4 #XR-305323
CNC-machined 50mm drive shaft for XRAY T2, T3 made from world-renowned top-secret HUDY Spring Steel™. This race-quality drive shaft is the smallest in the world, exclusively manufactured by HUDY. Drive shaft diff end has been strategically lightened to reduce rotating mass without compromising strength.
| 
收藏
勁正
嬲嬲