電單車已改speed300 摩打可否用回原裝金屬摩打齒

我想問已改speed300 motor 可否使用原裝金屬motor齒



[ 本帖最後由 Ken 於 2006-6-3 01:12 編輯 ]

原裝金屬motor齒粒机米都收唔死條軸,垃圾!

tks

我建議用番原裝膠齒....

我已買了膠齒，但紅星只得last一pack，想買多set做spare 都不可以

tks

唔驚!!過一排又返貨o架喇.....玩住先啦..哈哈

Hi,

Which Speed 300 motor you are running? Do you have the model number or URL? Any modification required?

Thanks.

300 Motor 條心粗少少，所以要用暴力才可迫隻齒入去。
用金屬齒仲要出動鎚仔添。

我用膠齒，在齒中用電鑽開大些便可，不須用暴力

鑽大隻摩打齒....小心玩得激會飛出呢....
個人做法都係用小小暴力最好.....

Thanks for the information!

What does 300 motor really mean? Is it the size of the motor? Which Speed 300 motor you guys are running? Do you have the model and URL?  Is Futaba MCR ESC able to handle Speed 300 motor (Manual said upto 280 size motor)  Is Speed 300 motor much faster than 28BB?

Thanks.

Speed 300 motor size [ 直徑同 kyosho 28bb 一樣,長度短 D] 不過要用落kyosho 電單車要加接合器先可以用到.
而 Futaba MCR ESC 用 Speed 300 motor 唔係太建議用,因為兩件頭輸出可能唔夠.
Speed 300 motor 係快過28bb 不過行車時間短及對架車損耗大.
http://www.hobby-lobby.com/speed300.htm

There are two Speed 300 (6v and 7.2v) Which one would be good for Kyosho ar?
Where i can get the 接合器?

Thanks.

大部份玩電單車都係用6v model 而 7.2v 我好似係hk未見有賣....其他師兄見有請報料.thx
接合器可以pm beebee 版主問問仲有冇,如果冇可用3 racing for 18仔 用接合器,不過要改少少個牙箱位先方便用到.

用gpm的金屬motor座開洞即可

Is this the right one with drilling a bigger hole?

http://cgi.ebay.com/GPM-ALLOY-GE ... QrdZ1QQcmdZViewItem


Is is necessary to upgrade Kyosho Gear & Sprocket with Speed 300 on it?

http://cgi.ebay.com/KYOSHO-GPW11 ... QrdZ1QQcmdZViewItem

原帖由 ckyan 於 2006-6-3 18:22 發表
大部份玩電單車都係用6v model 而 7.2v 我好似係hk未見有賣....其他師兄見有請報料.thx
接合器可以pm beebee 版主問問仲有冇,如果冇可用3 racing for 18仔 用接合器,不過要改少少個牙箱位先方便用到.

use the rc18t motor mount???

原帖由 rcplayer 於 2006-7-31 21:07 發表

use the rc18t motor mount???

可以咁講~~不過d位窄窄地...