原帖由 go2usie 於 2008-2-22 19:41 發表
hi Bro Bololo~ i had done the Refurbishmentof my 959 too~ i had put on the same 02H motor ~
please dont mind i would upload a lot of pic on your post~
My body is a lot better then yours, i will do t ...
原帖由 go2usie 於 2008-2-22 22:32 發表
bro tigar1, u have 959 too ?
i know u have a lot of antique~ lets show them up ~
原帖由 minimini 於 2008-2-23 01:22 發表
woooo.......good stuff ......
bro susie......you are using the Tamiya 24mm touring car wheels & tyres ??.......
原帖由 go2usie 於 2008-2-23 14:43 發表
do brothers think, we can replace it with the 1:12 Porsche 934 body on our chassis ??
just to adjust the offset of rim.... ??
or this tire size fit the 959 rims ???
原帖由 bololo 於 2008-2-23 20:10 發表
Sorry brother, the wheelbase of 934 is 190mm and 959 is around 210mm (measured by myself). Different is too big to fit.
原帖由 go2usie 於 2008-2-22 19:41 發表
hi Bro Bololo~ i had done the Refurbishmentof my 959 too~ i had put on the same 02H motor ~
please dont mind i would upload a lot of pic on your post~
My body is a lot better then yours, i will do t ...
原帖由 bololo 於 2008-2-23 20:10 發表
Sorry brother, the wheelbase of 934 is 190mm and 959 is around 210mm (measured by myself). Different is too big to fit.
原帖由 minimini 於 2008-2-24 00:03 發表
Hi bro bololo.........how about the width of 959 ?? (when compared with the 934)........ Thx !!
原帖由 bololo 於 2008-2-24 10:09 發表
Hi! The width of 934 is 167mm and 959 is 172mm (figure from Tamiya club), thanks!
原帖由 skleejames 於 2008-2-24 01:41 發表
very good job, especial the aluminium front and rear arms.
I have 959 too, but one of the broken front arm is lost by a careless guy who said he can copy an aluminium one for me, but..... ...
原帖由 bololo 於 2008-2-24 20:37 發表
Any brother know what kind of plastic of front and rear arm? Since these parts are most easy to be cracked and instant glue is always no function fror them.
原帖由 tiger1 於 2008-2-24 23:35 發表
Those should be polystyrene, which the whole car was made of. Too brittle.
原帖由 tiger1 於 2008-2-25 00:18 發表
I would try epoxy. However, the most common epoxy in HK is Aralite, which is not too good after a few years.
The best epoxy I have ever tried was 'JB Weld', not very common in HK.
Do ...
原帖由 fat_fat_cat 於 2008-2-29 11:33 發表
You can also try glue for woman using on nail, a mixture of powder and liquid, very strong, you can even drill or tapped the mixture. try try ar
原帖由 tiger1 於 2008-2-29 13:00 發表
Yes, those are acrylic resin (PMMA or polymethylmethacrylate resin), very strong, good for polystyrene material like 959. But only good for bonding plastic to plastic, got to be hard plastic too.
歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/) | Powered by Discuz! X3.2 |