RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: F104 JV 被撞重傷 [打印本頁]

作者: cyberkohk    時間: 2011-1-10 14:55
標題: F104 JV 被撞重傷
今天在JV又被撞斷尾軸 , MOTOR中軸都側O左都唔知點整 , 今天車子發揮良好玩O左半粒鐘都無事 , 不幸比人撞車尾當時右輪胎飛去 .
立即收工走人 . FORMULA好玩不過好易撞壞 .
作者: samuel20461    時間: 2011-1-10 15:00
Don't give up ching.
作者: ap    時間: 2011-1-10 15:03
f1係jv玩好似玩命,成日見f1俾人炒。
一炒便爛。
作者: ultra7    時間: 2011-1-10 15:03
回復 1# cyberkohk


    FORMULA好玩不過好易撞壞 << agree!
作者: buzzybee82    時間: 2011-1-10 15:04
jv咁多快車.....放架f 車落去等同於呀婆過馬路......唔撞死都嚇死!!!
作者: F3F    時間: 2011-1-10 15:06
好多野無得避免........無計
作者: mrpanda    時間: 2011-1-10 15:28
too bad 師兄
俾咩車種撞
食到好應吓
作者: sex8088    時間: 2011-1-10 15:40
i also have same case,  after JV need to go KWS buy parts everytime. good luck!
作者: speedo    時間: 2011-1-10 15:44
hi cyberkohk, what motor are u using?
作者: cyberkohk    時間: 2011-1-10 15:56
TEAM POWER MOTOR
唔知咩車皮帶四驅車又唔似星星 , 但F車直路加速比房車快 . 部車RUN順O左越來越好玩 , 但經常要整好肉痛.
作者: nel3838    時間: 2011-1-10 16:31
本帖最後由 nel3838 於 2011-1-10 16:33 編輯

C-Hing,  SAME SAME for me too, TWICE .... my poor F1零死 . . .

For me, things fixed:-
a) change to steel rear axle (around $35 from KWS, its much stronger - and only 15 gram heavier which is worthwhile).
b) change to one piece T Bar (use thinker ones 1.8mm is good, since JV has high rear grip anyways)
c) I too have Team Power motor.  And I too bent 2 motor shafts from JV accidents.  Although with some fine re-bending work at home, I managed to get both shafts straighten....... enough to play.  And you can order new Team Power shafts from 3Racing or Harmony in KWS.
d) bought tougher rear spoiler wings from Cat Shop in KWS (some japan option A/B).  The plastic is as tough as the Tamiya front bumper/wing, so good for absorbing rear impact.

And hopefully, in future, someone at JV will put anti-crash barriers by the lamp posts and breaks on the fast straight.  Very expensive straight . .. .  for us  .


PS: also avoid the track when there are too many super fast touring/4WD cars.......

Hope this helps.
作者: bowielum    時間: 2011-1-10 16:43
換摩打芯
作者: cyberkohk    時間: 2011-1-10 16:52
KWS 唔係間間模型鋪都有F104 OPTION 買 , 我多數去窩打老道買多因比較齊貨但會貴少少 .
B) KWS未見過有得買
作者: cyberkohk    時間: 2011-1-10 17:04
摩打芯如何回復中心位置???
作者: sai20092001    時間: 2011-1-10 17:21
原來飛黎飛去果個碌係你ga..
作者: nel3838    時間: 2011-1-10 17:49
摩打芯如何回復中心位置???
cyberkohk 發表於 2011-1-10 17:04


traditional bending method using Vice and Pliers.

Use the Motor Can body end bells to support the shaft, so that can spin and check after each bend.  Take little care and time, nothing special.  With luck, can get it quite good and straight.  Good luck.
作者: nel3838    時間: 2011-1-10 17:50
標題: hop
KWS 唔係間間模型鋪都有F104 OPTION 買 , 我多數去窩打老道買多因比較齊貨但會貴少少 .
B) KWS未見過有得買 ...
cyberkohk 發表於 2011-1-10 16:52


B) KWS  要 3Racing - order OR cat shop but expensive.  

But 那里 可以北买 呢?
作者: abcde    時間: 2011-1-10 19:13
chings....我通常會等d快車玩完或少車時先玩...咁會少d爛野同玩得開心d...
d快車通常都會等都十架八架先玩...佢地都係差不多時間無電...咁你先出車就會安全d...
作者: HERO34    時間: 2011-1-10 21:01
其實大家禮讓D、依D悲劇可以避免
作者: cyberkohk    時間: 2011-1-11 14:50
我已經買齊OPTION修理 , 不過我落場玩的經驗得最近幾個月 , 技術比起CHING當然有分別 . 所以大家請見諒 .
作者: nel3838    時間: 2011-1-11 21:08
我地都交好多学费ga..... 享受吧....
作者: tiger1    時間: 2011-1-12 07:28
Use steel shaft and forget about carbon shaft. Good luck
作者: longman0072    時間: 2011-1-12 12:44
so horrible.......the verdict is that F1 is funny but costly (to repair)~~~
作者: billgate803    時間: 2011-1-12 23:45
換完steel shaft , 一撞轉移斷T板
作者: billgate803    時間: 2011-1-12 23:46
不如換鋁"LAW C" 斷鋁"LAW C", 好過斷T板/斷碳軸
作者: nel3838    時間: 2011-1-13 12:49
不如換鋁"LAW C" 斷鋁"LAW C", 好過斷T板/斷碳軸
billgate803 發表於 2011-1-12 23:46


Good idea C-Hing,

But where to put 鋁"LAW C",
作者: z96282424    時間: 2011-1-13 17:06
換完steel shaft , 一撞轉移斷T板
billgate803 發表於 2011-1-12 23:45


未到T板住呀, 應該係歪犘打座先....
因為我就係咁XD

換番膠犘打座耐玩好多嫁~
作者: billgate803    時間: 2011-1-13 23:54
Good idea C-Hing,

But where to put 鋁"LAW C",
nel3838 發表於 2011-1-13 12:49



    I THINK最好全部地方
作者: billgate803    時間: 2011-1-13 23:54
未到T板住呀, 應該係歪犘打座先....
因為我就係咁XD

換番膠犘打座耐玩好多嫁~
z96282424 發表於 2011-1-13 17:06


咁都得?!




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/) Powered by Discuz! X3.2