RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 我的PROJECT 真.PRO-4 [打印本頁]

作者: kaidogg 時間: 2009-8-18 23:45
標題: 我的PROJECT 真.PRO-4
本帖最後由 kaidogg 於 2009-8-18 23:48 編輯

哈哈
好野
先多謝網友 EDISON 幫忙教路有關支架銲接問題

目標係呢架
[attach]293060[/attach]

好喇畫左圖咁多日今日終於開工動手
[attach]293057[/attach]

先屈個抵先
[attach]293058[/attach]

點知彎位太大╴ 其實都唔係好緊要但必要時會鋸左佢
[attach]293059[/attach]

作者: 葉生 時間: 2009-8-19 00:36

好期待完成品!!!

作者: po3117 時間: 2009-8-19 00:38
銅支

架車好正喎

作者: bcgg 時間: 2009-8-19 16:36
V記出手DIY車架!
期侍!加油!

作者: kaidogg 時間: 2009-8-19 16:55

V記出手DIY車架!
期侍!加油!
bcgg 發表於 2009-8-19 16:36

登錄/註冊後可看大圖

如果有你幫手我就唔使自己出馬啦哈哈

作者: ryancmlam 時間: 2009-8-19 20:32
add oil add oil

作者: 22年 時間: 2009-8-19 22:56
Victor兄你真夠喪！超期待大作完成一睹其奔走雄姿。

作者: kaidogg 時間: 2009-8-20 02:37
死啦用 MAPP GAS 好驚呀點算突然個心唔知點解好驚爆炸

作者: IS520 時間: 2009-8-20 09:27
樓主, 你用緊 "銅枝定係鋼枝" 黎呢？

仲有係幾多mm 直徑呀？

thks.

死啦用 MAPP GAS 好驚呀點算突然個心唔知點解好驚爆炸
kaidogg 發表於 2009-8-20 02:37

登錄/註冊後可看大圖

作者: kaidogg 時間: 2009-8-20 16:46
鋼枝 2.5 3 同 4都有

作者: kaidogg 時間: 2009-8-25 02:08
10# kaidogg

今日終於 DICK 起心乾
燒左一邊車架
燒完好似唔岩位有D R R 地 FEEL

作者: matchbox 時間: 2009-8-25 02:12
Vitor, 好正wor

作者: 自由大帝 時間: 2009-8-25 19:11
哇~~期待期待！！

作者: kaidogg 時間: 2009-8-26 00:28
而家 2.5MM 同 3.5MM 都太林
主力支架好可能需要D 粗D既

作者: kaidogg 時間: 2009-8-27 20:27
14# kaidogg

今日整左個尾架
[attach]295691[/attach]

[attach]295692[/attach]

作者: matchbox 時間: 2009-8-27 22:23
Victor, 好似粗d會質感會好d同實用d

作者: kaidogg 時間: 2009-8-27 22:34
粗D 好Q難屈架 ...
冇咩奶力屈
抱阿仔出街都抱到支力

作者: bcgg 時間: 2009-8-28 12:45

14# kaidogg

今日整左個尾架
295691

295692
kaidogg 發表於 2009-8-27 20:27

登錄/註冊後可看大圖

You are absolutely crazy!!!

作者: kaidogg 時間: 2009-8-29 14:07

You are absolutely crazy!!!
bcgg 發表於 2009-8-28 12:45

登錄/註冊後可看大圖

wa hahahahaah

作者: matchbox 時間: 2009-8-29 14:51
聽日可能落兩, 如落雨就要同TKO講再見~~

作者: kaidogg 時間: 2009-9-3 18:20
由於換左新車殼
所以由頭整過晒
而家進度係咁
今次仲GOOD FIT 添

好想快D完成佢

[attach]297657[/attach]
[attach]297658[/attach]
[attach]297659[/attach]
[attach]297660[/attach]

作者: bcgg 時間: 2009-9-4 14:25

由於換左新車殼
所以由頭整過晒
而家進度係咁
今次仲GOOD FIT 添

好想快D完成佢

297657
297658
297659
297660
kaidogg 發表於 2009-9-3 18:20

登錄/註冊後可看大圖

V記, 請問依個係乜gearbox?

作者: matchbox 時間: 2009-9-4 14:34

V記, 請問依個係乜gearbox?
bcgg 發表於 2009-9-4 14:25

登錄/註冊後可看大圖

好似係AX10

作者: bcgg 時間: 2009-9-4 14:41

好似係AX10
matchbox 發表於 2009-9-4 14:34

登錄/註冊後可看大圖

用慢爬的去跑,ok嗎?, 我也想買!

作者: matchbox 時間: 2009-9-4 14:48
入面係金屬齒

作者: bcgg 時間: 2009-9-4 14:53

入面係金屬齒
matchbox 發表於 2009-9-4 14:48

登錄/註冊後可看大圖

强哥知否有冇淨Gear box 連牙買呢? 如有,大約多小$呢?

作者: matchbox 時間: 2009-9-4 15:01

强哥知否有冇淨Gear box 連牙買呢? 如有,大約多小$呢?
bcgg 發表於 2009-9-4 14:53

登錄/註冊後可看大圖

Gear box 連牙 around $2xx

作者: powis 時間: 2009-9-4 15:02
I think the rod is not 粗 enough wor......otherwise when the car crash...ai....>_< just afraid wasted ur time!

作者: bcgg 時間: 2009-9-4 15:06

Gear box 連牙 around $2xx
matchbox 發表於 2009-9-4 15:01

登錄/註冊後可看大圖

煩多你一下.......那裏有售/訂?

Thanks

作者: matchbox 時間: 2009-9-4 16:27

煩多你一下.......那裏有售/訂?

Thanks
bcgg 發表於 2009-9-4 15:06

登錄/註冊後可看大圖

偉X, remember to buy the diff gear too.

作者: kaidogg 時間: 2009-9-4 17:08

I think the rod is not 粗 enough wor......otherwise when the car crash...ai....>_< just afraid wasted ur time!
powis 發表於 2009-9-4 15:02

登錄/註冊後可看大圖

hihi
Which rod ? I so scare now ...
the ORANGE rod or the SILVER rod ?
or the plastic Joinning ?
Help .. so scare wor ....

作者: kaidogg 時間: 2009-9-4 17:11

用慢爬的去跑,ok嗎?, 我也想買!
bcgg 發表於 2009-9-4 14:41

登錄/註冊後可看大圖

Correct
AX10 (SCX10 same) $260 i think
get Diff Gear too is $32 i think
Wei X upstairs ar ...

PS .. It's for 1/10 if you want Longer ..need buy Extension @ G lok $150
and have other too

THIS part is the Most expansive part of my car
$26x + 150 + 3x + 30((rod)
the Roll cage only $8 one stick .. i buy jor 10 .. MAX is $80 hahaaahahhaha

BCGG U want make one too ?
GOOD .. wait your better design version

作者: bcgg 時間: 2009-9-4 17:33

Correct
AX10 (SCX10 same) $260 i think
get Diff Gear too is $32 i think
Wei X upstairs ar ...

PS .. It's for 1/10 if you want Longer ..need buy Extension @ G lok $150
and have other too ...
kaidogg 發表於 2009-9-4 17:11

登錄/註冊後可看大圖

Thanks
我覺得"most expansive part" 係你D心機!

作者: kaidogg 時間: 2009-9-4 17:44

Thanks
我覺得"most expansive part" 係你D心機!
bcgg 發表於 2009-9-4 17:33

登錄/註冊後可看大圖

hehe AGREE thanks
我覺符呢架車整完出黎MAYBE 行唔到 XD

作者: bcgg 時間: 2009-9-4 18:07

hehe AGREE thanks
我覺符呢架車整完出黎MAYBE 行唔到 XD
kaidogg 發表於 2009-9-4 17:44

登錄/註冊後可看大圖

其實如果玩快...用依種波箱,好似有D..........即係會唔會用番D搖臂設計...好D呢?

作者: bcgg 時間: 2009-9-4 18:09
行就一定行得到嘅...問題係行得好唔好囉...

作者: bcgg 時間: 2009-9-4 18:11
不如個尾用埋頭嗰份,用拉捍lock左個轉向,仲可以較Toe-in添....

作者: kaidogg 時間: 2009-9-4 23:22

其實如果玩快...用依種波箱,好似有D..........即係會唔會用番D搖臂設計...好D呢?
bcgg 發表於 2009-9-4 18:07

登錄/註冊後可看大圖

真既 PRO-4 PRO-2 係咁既設計架
真車就好好行喇
唔知玩具會點
始終個重量比例好緊要
真車架架都成千KG 而且800 BPS 起步
頭尾重量分報得好好岩岩好
JUMP 果時就唔會有事喇

我估我架車起左貸玩得都仲要有排TUNE D 重量分報

作者: bcgg 時間: 2009-9-7 14:51

真既 PRO-4 PRO-2 係咁既設計架
真車就好好行喇
唔知玩具會點
始終個重量比例好緊要
真車架架都成千KG 而且800 BPS 起步
頭尾重量分報得好好岩岩好
JUMP 果時就唔會有事喇

我估我架車起左貸玩得都仲要 ...
kaidogg 發表於 2009-9-4 23:22

登錄/註冊後可看大圖

我又學多樣野了!

作者: kaidogg 時間: 2009-9-11 01:41
本帖最後由 kaidogg 於 2009-9-11 01:43 編輯

整左個底盤小小啦唔算整晒
原來整個位比SERVO 比想像中難
今晚收工

A 手BAI 可能向下下到咁 ...
[attach]299815[/attach]

正面
[attach]299814[/attach]

加左小小則面既支架
[attach]299816[/attach]
[attach]299817[/attach]

整好左大約會係咁
可能要用 9551 先夠位放 SERVO
[attach]299818[/attach]

作者: -69- 時間: 2009-9-11 05:38
Keep going ! very nice !! ;-)

作者: powis 時間: 2009-9-11 14:44
How thick of the plate of 底盤 ?? looks like very thin...

作者: kaidogg 時間: 2009-9-11 14:48

How thick of the plate of 底盤 ?? looks like very thin...
powis 發表於 2009-9-11 14:44

登錄/註冊後可看大圖

I think It's 1.5mm .. It's scrap metal from old computer case hahahahaa

作者: powis 時間: 2009-9-11 20:54

I think It's 1.5mm .. It's scrap metal from old computer case hahahahaa
kaidogg 發表於 2009-9-11 14:48

登錄/註冊後可看大圖

very thin wor....

作者: kaidogg 時間: 2009-9-12 01:44

very thin wor....
powis 發表於 2009-9-11 20:54

登錄/註冊後可看大圖

No worry ga
After Burn the 支架 to it
the 支架 will 拉 it ... so it won't bend

lol 中英夾雜

作者: kaidogg 時間: 2009-9-16 01:54
本帖最後由 kaidogg 於 2009-9-16 02:03 編輯

45# kaidogg
佢地終於合體喇

作者: powis 時間: 2009-9-16 10:01

45# kaidogg
佢地終於合體喇
kaidogg 發表於 2009-9-16 01:54

登錄/註冊後可看大圖

Good luck man!

作者: 1312 時間: 2009-9-16 10:39
C hing ......good creative

作者: deadmatch 時間: 2009-9-16 11:42
long tme not back to rc-evo.
this post is quite interesting.
however, i do concern on some points of this car as i have made this type of cars before also.
1. i support kaidogg that the 支架WILL 拉, AND it will not bend. however, i do think that it will cause the whole structure broken once crash.
2. the structure seems like too thin and week. better get a thicker and stronger material to do that.

Anyway, I do support DIY and your spirit and idea is really good. I think you maybe just mis-use of the materials. That is what DIy-ers will try when learning and testing. By be sure that, take every brother in this forum opinion to consider and you will finally get a good car.

作者: kaidogg 時間: 2009-9-16 17:13

long tme not back to rc-evo.
this post is quite interesting.
however, i do concern on some points of this car as i have made this type of cars before also.
1. i support kaidogg that the 支架WILL 拉 ...
deadmatch 發表於 2009-9-16 11:42

登錄/註冊後可看大圖

yes yes very good comment ....
as u said ... Have to Test (when It's finally done and still have long way to go hahaaha)
I can't say that It's structure is strong enough or not

I just use What ever I can get easily and I can hanadle ..

EG . metal board too thick ? I can't cut myself
metal rod too think I can't bend then or Weld them

so ... base on what I can use I make this current design and adjust it along the way

really thanks for the comment .. really helpful and useful

ps about the 拉 part ... is I THINK it will work only hahaaahahhaa

PS2 i do think that it will cause the whole structure broken once crash.
I really really really hope that this point is wrong ... if really happen .. i want cry

作者: deadmatch 時間: 2009-9-16 20:45

yes yes very good comment ....
as u said ... Have to Test (when It's finally done and still have long way to go hahaaha)
I can't say that It's structure is strong enough or not

I just use Wha ...
kaidogg 發表於 2009-9-16 17:13

登錄/註冊後可看大圖

M.....actually it is really different for making a real car and a rc.
give you two pictures of what i am working now.
i am not saying this is good enough but i do think it must stronger structure than your car for crashing.XD
don't hope for the point, the whole structure links together and even a small parts damage needed to change the whole chassis......

作者: kaidogg 時間: 2009-9-16 20:52

M.....actually it is really different for making a real car and a rc.
give you two pictures of what i am working now.
i am not saying this is good enough but i do think it must stronger structure ...
deadmatch 發表於 2009-9-16 20:45

登錄/註冊後可看大圖

Why not solid rear axel ?

作者: deadmatch 時間: 2009-9-16 20:58
once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC

作者: kaidogg 時間: 2009-9-16 21:05

once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC
deadmatch 發表於 2009-9-16 20:58

登錄/註冊後可看大圖

but if you install Roll Bar system it will be ok ?

作者: kaidogg 時間: 2009-9-16 21:07
54# kaidogg

by the way
my car is based on this real truck
so ... should be strong enough
I tried to THROW my cage out the windows and is ok wor
I live in 1st floow

作者: deadmatch 時間: 2009-9-16 21:09
you know that the sudden impact is much much bigger .....
i know your car is base on the real car. but for a real car , when it crash, it will collapse also.....
but for RC don't.......

作者: kaidogg 時間: 2009-9-16 21:15
Ture Ture

so ... I HOPE i won't crash HARD
people don't crash me please hahaahah
by the way
I don't think my car will Run well too ... but I just want to Build it ... everything is AFTER WORDS
hahaahahah

support me support me la

ps I really mean that I throw out the window

作者: kaidogg 時間: 2009-9-16 21:16
once damping in the solid rear axial, the 4-link system will cause a angle bending in the solid rear axial. that will cause a little effect on the straight motion of the RC
deadmatch 發表於 2009-9-16 20:58
but if you install Roll Bar system it will be ok ?

作者: deadmatch 時間: 2009-9-16 21:19
it will be better.
you idea is good, but better for choosing the material.
i think use 2-3 mm thick aluminium alloy will better
also, 4mm steel bar to make the chassis will be the best.

作者: kaidogg 時間: 2009-9-16 21:27

it will be better.
you idea is good, but better for choosing the material.
i think use 2-3 mm thick aluminium alloy will better
also, 4mm steel bar to make the chassis will be the best.
deadmatch 發表於 2009-9-16 21:19

登錄/註冊後可看大圖

aluminium alloy Can't be Weld wor ...
I have that at home but when I weld it ... it Melts

作者: deadmatch 時間: 2009-9-16 21:29
yes, use screw those stuff la.
it can help you to better to do maintaince for the car

作者: kaidogg 時間: 2009-9-16 21:37

yes, use screw those stuff la.
it can help you to better to do maintaince for the car
deadmatch 發表於 2009-9-16 21:29

登錄/註冊後可看大圖

cannot la T_T
I have limited skills
一係WELD 一係全車 SCREWS AND NUTS
BUT ...... using aluminium alloy plates is hard to get the shape of what I want
anyway let me finish this car ... if it's really that suck as you said it would be ... then I start new project haha
and put this car into my 貢品區

but most important is ... you give me very good suggestion
thanks thanks thanks

作者: deadmatch 時間: 2009-9-16 21:56
nvm, i am just a kid only.
hope can help you brother

作者: kaidogg 時間: 2009-9-16 21:59

nvm, i am just a kid only.
hope can help you brother
deadmatch 發表於 2009-9-16 21:56

登錄/註冊後可看大圖

yes yes you already helped me alot
for my Future car
this Prototype car have problem already hahaahaah
I just found out .... the SERVO holder is in the wrong place .... hahahahaahahahahahaahahaaha

damn ..

作者: deadmatch 時間: 2009-9-16 22:04
servo holder?

作者: jeffip97 時間: 2009-9-16 23:33
[quote]
yes yes you already helped me alot
for my Future car
this Prototype car have problem already hahaahaah
I just found out .... the SERVO holder is in the wrong place .... hahahahaahahahahahaahaha ...

u r already very strong, can DIY a car, add oil la, remember to show us photo wor

作者: powis 時間: 2009-9-17 00:14

Ture Ture

so ... I HOPE i won't crash HARD
people don't crash me please hahaahah
by the way
I don't think my car will Run well too ... but I just want to Build it ... everything is AFTER WORD ...
kaidogg 發表於 2009-9-16 21:15

登錄/註冊後可看大圖

I like you that you throw ur cage from window!

作者: salemsalem_1999 時間: 2009-9-17 02:47
cool!!!!!!!!!!!!!!!

作者: kaidogg 時間: 2009-9-18 01:33
AIYA BRAIN STORM AGAIN
SERVO 擺位諗唔掂

作者: deadmatch 時間: 2009-9-18 09:00
give some pictures to all brothers in rc-evo and maybe we can help you.

作者: kaidogg 時間: 2009-9-20 16:24
PASSWORD WRONG ?
PLEase fix

400B2860859E+C95C6E7A6D28_FDZone.ORG_P2MSKTQ1U3F_avfun.ORG_rNkn2CA_TWFCB.COM_EH6K8207936Q5A6_Safe秘境_HKODSWE

複製代碼

作者: L.c80 時間: 2009-9-20 21:54
正啊```。

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://www.rc-evo.com/xbbs/)